Mitsubishi Galant 9G. Manual — part 39
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-152
STEP 9. Check ETACS-ECU connector C-219 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-219 in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that all the doors can be locked and
unlocked normally.
STEP 10. Check the wiring harness between ETACS-ECU
connector C-219 (terminals 12 and 13) and front door lock
actuator (RH) connector E-05 (terminals 4 and 6).
AC305413 AG
CONNECTOR: C-219
JUNCTION BLOCK SIDE
JUNCTION BLOCK
(REAR VIEW)
AC305413 AG
CONNECTOR: C-219
JUNCTION BLOCK SIDE
JUNCTION BLOCK
(REAR VIEW)
AC305333
AH
CONNECTOR: E-05
E-05 (B)
HARNESS SIDE
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-153
NOTE: Also check intermediate connector C-12 and junction
block connector C-211 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connector. If intermediate
connector C-12 or junction block connector C-211 is damaged,
repair or replace the damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between ETACS-ECU connector
C-219 (terminals 12 and 13) and front door lock actuator
(RH) connector E-05 (terminals 4 and 6) in good
condition?
YES : Replace the ETACS-ECU. Verify that all the doors
can be locked and unlocked normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary.
STEP 11. Check rear door lock actuator (LH) connector
E-18 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is rear door lock actuator (LH) connector E-18 in good
condition?
YES : Go to Step 12.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that all the doors can be locked and
unlocked normally.
AC305233
CONNECTOR:C-12
AB
AC305415AH
CONNECTOR: C-211
C-211
HARNESS SIDE
JUNCTION BLOCK
(FRONT VIEW)
AC305262
E-18 (B)
HARNESS SIDE
CONNECTOR: E-18
AJ
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-154
STEP 12. Check the rear door lock actuator (LH).
Remove the rear door lock actuator (LH). The illustration shows
when the door lock actuator is viewed from outside the door.
Refer to GROUP 42
− Door Handle and Latch
.
Q: Does the rear door lock actuator (LH) work normally?
YES : Go to Step 13.
NO : Replace the rear door lock actuator (LH). Verify that
all the doors can be locked and unlocked normally.
STEP 13. Check ETACS-ECU connector C-219 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-219 in good condition?
YES : Go to Step 14.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that all the doors can be locked and
unlocked normally.
LEVER
POSITION
BATTERY
CONNECTION
LEVER
OPERATION
At the "LOCK"
position
• Connect terminal 6
to the negative
battery terminal
• Connect terminal 4
to the positive
battery terminal
The lever moves
from the "LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position
• Connect terminal 4
to the negative
battery terminal
• Connect terminal 6
to the positive
battery terminal
The lever moves
from the
"UNLOCK" position
to the "LOCK"
position.
1 2 3
4 5 6
AC210906
A
VIEW A
LOCK
UNLOCK
LEVER
AB
AC305413 AG
CONNECTOR: C-219
JUNCTION BLOCK SIDE
JUNCTION BLOCK
(REAR VIEW)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-155
STEP 14. Check the wiring harness between ETACS-ECU
connector C-219 (terminals 12 and 13) and rear door lock
actuator (LH) connector E-18 (terminals 4 and 6).
NOTE: Also check intermediate connector D-19 and junction
block connector C-204 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connector. If intermediate
connector D-19 or junction block connector C-204 is damaged,
repair or replace the damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between ETACS-ECU connector
C-219 (terminals 12 and 13) and rear door lock actuator
(LH) connector E-18 (terminals 4 and 6) in good
condition?
YES : Replace the ETACS-ECU. Verify that all the doors
can be locked and unlocked normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that all
the doors can be locked and unlocked.
AC305413 AG
CONNECTOR: C-219
JUNCTION BLOCK SIDE
JUNCTION BLOCK
(REAR VIEW)
AC305262
E-18 (B)
HARNESS SIDE
CONNECTOR: E-18
AJ
AC305415AJ
CONNECTOR: C-204
HARNESS SIDE
JUNCTION BLOCK
(FRONT VIEW)
AC400532
AC
CONNECTOR: D-19
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст