Mitsubishi Galant 9G. Manual — part 984
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-236
STEP 6. Check harness connector B-32 at intermediate
connector for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 13.
STEP 7. Measure the right bank injector resistance at
intermediate connector B-32.
(1) Disconnect the intermediate connector B-32.
(2) Measure the resistance between each injector side
connector terminal.
a. Measure the resistance between terminal No. 5 and No.
9 when measuring No. 1 cylinder.
b. Measure the resistance between terminal No. 9 and No.
10 when measuring No. 3 cylinder.
c. Measure the resistance between terminal No. 4 and No.
9 when measuring No. 5 cylinder.
• Resistance should be between 10.5 and 13.5 ohms [at
20
°C (68° F)].
Q: Is the measured resistance between 10.5 and 13.5 ohms
[at 20
°C (68°F)]?
YES : Go to Step 10.
NO : Go to Step 8.
AK303053
3
4
5
8
9
1
2
6
7
10
CONNECTOR: B-32
HARNESS CONNECTOR:
COMPONENT SIDE
AB
B-32 (B)
AK303053
3
4
5
8
9
1
2
6
7
10
CONNECTOR: B-32
HARNESS CONNECTOR:
COMPONENT SIDE
AB
B-32 (B)
1
2 3
6
7 8
4 5
9 10
AK203093
B-32
INTERMEDIATE
CONNECTOR
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-237
STEP 8. Check harness connector B-03, B-04, B-01 at right
bank injector for damage.
(1) Remove the intake manifold.
(2) Check the right bank injector connector, which deviates
from the standard value at Step 7.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 13.
STEP 9. Check the right bank injector.
(1) Check the right bank injector, which deviates from the
standard value at Step 7.
(2) Measure the resistance between injector side connector
terminal No. 1 and No. 2.
Standard value: 10.5
− 13.5 ohms [at 20°C (68°F)]
Q: Is the measured resistance between 10.5 and 13.5 ohms
[at 20
°C (68°F)]?
YES : Repair harness wire between injector intermediate
connector and right bank injector connector because
of harness damage. Then go to Step 13.
NO : Replace the injector. Then go to Step 13.
AK303055
M
1
2
CONNECTOR: B-01, B-03, B-04
AB
B-01 (GR)
B-03 (GR)
B-04 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK303055
M
1
2
CONNECTOR: B-01, B-03, B-04
AB
B-01 (GR)
B-03 (GR)
B-04 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK000559
2
1
INJECTOR SIDE
CONNECTOR
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-238
STEP 10. Check harness connector B-22, B-23 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 13.
AK303057
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
CONNECTORS: B-22, B-23
B-22 (B)
AB
B-23
B-22 HARNESS CONNECTOR:
COMPONENT SIDE
B-23 HARNESS CONNECTOR:
COMPONENT SIDE
PCM
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-239
STEP 11. Check for harness damage between right bank
heated oxygen sensor (front) connector B-09 (terminal No.
4) and PCM connector B-22 (terminal No. 92).
Q: Is the harness wire in good condition?
YES : Go to Step 12.
NO : Repair it. Then go to Step 13.
1
2
3
4
AK303048
B-09 (B)
CONNECTOR: B-09
THROTTLE BODY
RIGHT BANK
HEATED OXYGEN
SENSOR (FRONT)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст