Mitsubishi Galant 9G. Manual — part 476

DRIVE SHAFT ASSEMBLY

TSB Revision

FRONT AXLE

26-24

2. Use special tools MB990890, MB990938, and MB990934 to

press the dust seals into the center bearing bracket until
they are flush with each other.

3. Apply repair kit grease to the lip of each dust seal.

.

>>E<<INNER SHAFT <3.8L-RH> INSTALLATION

1. Use special tool MB991172 to hold the center bearing inner

race, and then press-in the inner shaft.

2. Apply repair kit grease to the inner shaft spline, then press fit

it into the PTJ case.
NOTE: When press-fitting the inner shaft into the PTJ case,
apply a thin coat of repair kit grease to the dust seal outer lip
part and the outside edge of the PTJ axial part.

.

AC101696

MB990890

DUST
SEAL
INNER

AC

AC101697

MB990938

MB990934

MB990890

DUST SEAL
OUTER

AC

AC101698

MB991172

INNER SHAFT

AC

AC205847

AC305786

PTJ CASE

INNER SHAFT

AB

DRIVE SHAFT ASSEMBLY

TSB Revision

FRONT AXLE

26-25

>>F<< TJ CASE <2.4L>/PTJ CASE <3.8L>
INSTALLATION

CAUTION

The drive shaft joint use special grease. Do not mix old
and new or different types of grease.
After applying the specified grease to the TJ case or PTJ case,
insert the drive shaft and apply grease again.

Specified grease: Repair kit grease

Amount to use <2.4L-LH>: 140

± 10 g (4.9 ± 0.3

ounces)

Amount to use <2.4L-RH>: 130

± 10 g (4.6 ± 0.3

ounces)

Amount to use <3.8L>: 220

± 10 g (7.8 ± 0.3 ounces)

NOTE: The grease in the repair kit should be divided in half for
use, respectively, at the joint and inside the boot.

.

>>G<< TJ BOOT BAND (SMALL) <2.4L>/PTJ
BOOT BAND (SMALL) <3.8L>/TJ BOOT BAND
(LARGE) <2.4L>/PTJ BOOT BAND (LARGE)
<3.8L> INSTALLATION

Set the TJ boot bands or PTJ boot bands at the specified dis-
tance in order to adjust the amount of air inside the TJ boot or
PTJ boot, and then tighten the TJ boot band (small) or PTJ
boot band (small), TJ boot band (large) or PTJ boot band
(large) securely.

Standard value (A): 85

± 3 mm (3.35 ± 0.12 inches)

INSPECTION

M1261003800163

• Check the drive shaft for damage, bending or corrosion.

• Check the inner shaft for damage, bending or corrosion.

• Check the drive shaft spline part for wear or damage.

• Check the inner shaft spline part for wear or damage.

• Check the spider assembly for roller rotation, wear or corro-

sion.

• Check the groove inside TJ case or PTJ case for wear or

corrosion.

• Check the boots for deterioration, damage or cracking.

• Check the center bearing for seizure, discoloration or

roughness of rolling surface.

• Check the dust cover for damage or deterioration.

AC102656 AC

AC102657

A

AC

DRIVE SHAFT ASSEMBLY

TSB Revision

FRONT AXLE

26-26

BJ BOOT REPLACEMENT

M1261005200394

Required Special Tool:
MB991561:Boot Band Crimping Tool
1. Remove the boot bands (large and small).

NOTE: The boot bands cannot be re-used.

2. Remove the BJ boot.
3. Wrap a plastic tape around the shaft spline, and assemble

the boot band and BJ boot.

4. Align the center groove on the BJ boot small end with the

shaft groove.

5. Turn the adjusting bolt on special tool MB991561 so that the

size of the opening (W) is at the standard value.

Standard value (W): 2.9 mm (0.11 inch)

<If it is larger than 2.9 mm (0.11 inch)> Tighten the

adjusting bolt.

<If it is smaller than 2.9 mm (0.11 inch)> Loosen the

adjusting bolt.

NOTE: The value of W will change by approximately 0.7 mm
(0.03 inch) for each turn of the adjusting bolt.
NOTE: The adjusting bolt should not be turned more than
once.

6. Position the BJ boot band (small) so that there is even

clearance at either end (A and B).

AC102658

AC102659

AC102660

W

MB991561

STOPPER

ADJUSTING BOLT

AC

AC102661AC

BOOT

A

BOOT BAND
(SMALL)

B

PROJECTION

DRIVE SHAFT ASSEMBLY

TSB Revision

FRONT AXLE

26-27

CAUTION

• Secure the drive shaft in an upright position and clamp

part of the boot band to be crimped securely in the jaws
of special tool MB991561.

• Crimp the boot band until the special tool touches the

stopper.

7. Use special tool MB991561 to crimp the boot band (small).

8. Check that the crimping amount (C) of the boot band is at

the standard value.

Standard value (D): 2.4

− 2.8 mm (0.09 − 0.11 inch)

<If the crimping amount is larger than 2.8 mm (0.11

inch)>
Readjust the value of (W) in step 5 according to the
following formula, and then repeat the operation in
step 7.
W = 5.5 mm (0.22 inch)

− D

Example: If D = 2.9 mm (0.11 inch), then W = 2.6 mm
(0.10 inch).

<If the crimping amount is smaller than 2.4 mm (0.09

inch)>
Remove the EBJ boot band, readjust the value of
(W) in step 5 according to the following formula,
and then repeat the operations in steps 6 and 7
using a new EBJ boot band.
W = 5.5 mm (0.22 inch)

− D

Example: If D = 2.3 mm (0.09 inch), then W = 3.2
mm (0.13 inch).

9. Check that the boot band is not sticking out past the place

where it has been installed. If the boot band is sticking out,
remove it and then repeat steps 6 to 8, using a new boot
band.

CAUTION

The drive shaft joint uses special grease. Do not mix old
and new or different types of grease.
10.Fill the inside of the boot with the specified amount of the

specified grease.

Specified grease: Repair kit grease

Amount to use <2.4L>: 120

± 10 g (4.2 ± 0.3 ounces)

Amount to use <3.8L>: 165

± 10 g (5.8 ± 0.3 ounces)

AC102663 AC

MB991561

AC102662

C

AD