Mitsubishi L200. Manual — part 552
DOOR SASH TAPE <VEHICLES WITH WIDE FENDER>
EXTERIOR
51-24
DOOR SASH TAPE
REMOVAL AND INSTALLATION
M1511024101016
Pre-removal and Post-installation Operation
• Front Door Sash Trim Removal and Installation (Refer to
GROUP 52A, Door Trim for Club Cab and for Double
Cab)
• Door Opening Weatherstrip Outer Removal and Installa-
tion (Refer to GROUP 42, Window Glass Runchannel and
Door Opening Weatherstrip .)
• Door Window Glass Runchannel Removal and Installation
(Refer to GROUP 42, Window Glass Runchannel and
Door Opening Weatherstrip .)
• Door Beltline Moulding Removal and Installation (Refer to
GROUP 42, Window Glass Runchannel and Door Open-
ing Weatherstrip .)
• Outside Mirror Removal and Installation (Refer to
.)
AC500616
A
B
F
F
C
C
B
E
D
D
E
A
1
2
AB
<Club cab>
AC500618
A
B
B
B
K
K
B
G
G
H
E
E
E
J
J
I
I
E
H
A
3
5
6
7
4
AB
<Double cab>
AC502531
AC500624
AC500619
AC500622
AC500623
AC500627
AC500621
AC502494
AC500626
AC500628
AC500620
AC500625
AB
Section D – D
4.1
3.0
2
Section E – E
3.0
Beltline moulding
Centre pillar
Centre pillar
Centre pillar
2, 4, 6
Section F – F
3.0
2
Section G – G
3.0
3.0
Overlap: 3
Overlap: 3
5
4
3
7
6
Section H – H
3.0
3.0
4.1
4.1
5
4
6
Section I – I
3.0
5
4, 6
Section J – J
5
Section K – K
18.2
3.5
Weatherstrip
7
Section A – A
Section B – B
3.0
3.7
4.1
Unit: mm
Door mirror
assembly
1, 3
1, 3, 7
Section C – C
3.0
Overlap: 3
2
1
Removal steps <Club cab>
<<
A
>>
>>
A
<<
1.
Door sash tape front
<<
A
>>
>>
A
<<
2.
Door sash tape rear
DOOR SASH TAPE <VEHICLES WITH WIDE FENDER>
EXTERIOR
51-25
Removal steps <Double cab>
<<
A
>>
>>
A
3.
Door sash tape front
<<
A
>>
>>
A
4.
Door sash tape rear
<<
A
>>
>>
A
5.
Centre pillar tape
DOOR SASH TAPE <VEHICLES WITH WIDE FENDER>
EXTERIOR
51-26
REMOVAL SERVICE POINT
<<A>> DOOR SASH TAPES/CENTRE PILLAR
TAPE REMOVAL
CAUTION
Pay attention to keep from getting burned by hot
door panel or tapes.
1. Use a hair drier to warm the tape.
2. Peel the tip of the tape with your finger, and then
peel off the tape parallel to the application
surface.
<<
A
>>
>>
A
<<
6.
Rear door sash tape front
<<
A
>>
>>
A
<<
7.
Rear door sash tape rear
Removal steps <Double cab>
DOOR SASH TAPE <VEHICLES WITH WIDE FENDER>
EXTERIOR
51-27
INSTALLATION SERVICE POINT
>>A<< DOOR SASH TAPES/CENTRE PILLAR
TAPE INSTALLATION
CAUTION
• The ambient temperature should be 20 - 30°C.
Ensure that the working area is clean. Tape
application should be done at ambient tem-
perature of 25
°C.
• If ambient temperature is less than 15°C, heat
the tape and application surface to a tempera-
ture of 20 - 30
°C. If ambient temperature is
35
°C or higher, cool down.
• The adhesive property of the tape is deterio-
rated at low temperature, so tape may come
adrift easily. Meanwhile, it gets softened at hot
temperature.
• When beginning to apply the tape, pay partic-
ular attention. If the end of the tape cannot be
applied to the specified position with an accu-
racy of less than 1 mm, it may cause the poor
appearance or adhesion.
•
AC303428
40 to 50˚
30 to 45˚
10 to 20 mm
10 to 20 mm
AB
MB990528
MB990528
Door sash tape
Door sash tape
Backing paper
Backing paper
<Pushing direction>
<Pulling direction>
3 to 7 cm/sec.
3 to 7 cm/sec.
Use the special tool stripe tape spatula
(MB990528) to apply the tape with a steady
pace and pressure. If you do not apply the
tape with a steady pace or pressure, or abort
the application, a shallow groove (lateral
groove called as "Shock line") may be
present on the tape surface. Meanwhile, if you
apply it too quickly, air bubbles may be
formed under the tape.
1. Wrap a soft cloth (synthetic fibre) around the tip of
the special tool(MB990528).
2. Use the parts cleaner (MZ100387 or equivalent)
to degrease the tape application surface.
3. Wipe away dirt from the tape.
4. Apply the door sash and centre pillar tapes
according to the procedures below.
AC402197
AB
MB990528
Tape
Backing paper
(1) Peel off the backing paper of the tape.
(2) Apply the tape and press it by using the
special tool.
AC402198
AB
MB990528
Tape
1
2
3
(3) Press the tape at the stepped part of the panel
in the following procedure.
1. Apply the tape onto the top plain part.
2. Next, apply onto the stepped part.
3. Finally, apply onto the bottom plain part.
AC303415
AB
MB990528
120˚
60˚
Hemming part
(4) Press the tape at the panel folded areas
(hemming part) at 3 steps (60
°, 120° and
holding), while rolling it toward the vehicle
inside.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст