Mitsubishi L200. Manual — part 778
RV METER
CHASSIS ELECTRICAL
54A-479
DIAGNOSIS PROCEDURE
STEP 1. Check the function type in the service
mode.
Check that the function type is set as 3 or 4 in the
service mode. (Refer to
Q: Is the check result satisfactory?
YES :
Go to Step 2
NO :
Set the function type again in the service
mode, and recheck the trouble symptom.
(Refer to
.)
STEP 2. Check the RV meter.
Check that the average vehicle speed and the aver-
age fuel consumption are displayed normally, and
check that the connection with the vehicle speed
sensor is normal.
Q: Is the check result satisfactory?
YES :
Go to Step 3
NO :
Perform the troubleshooting, Inspection
Procedure 2: "The drive information is not
displayed normally". (Refer to
STEP 3. Check the following connector: A-36
ambient air temperature sensor
Q: Is the check result normal?
YES :
Go to Step 4
NO :
Repair the defective connector.
STEP 4. Check the ambient air temperature
sensor.
Check the ambient air temperature sensor
.
Q: Is the check result normal?
YES :
Go to Step 5
NO :
Replace the ambient air temperature
sensor.
STEP 5. Check the following connector: C-171 RV
meter connector
Q: Is the check result normal?
YES :
Go to Step 6
NO :
Repair the defective connector.
AC903897
AB
Connector: A-36
Harness side
A-36 (B)
AC903856
Connector: C-171 <LHD>
AY
Harness side
C-171 (GR)
AC903868
Connector: C-171 <RHD>
BQ
Harness side
C-171 (GR)
RV METER
CHASSIS ELECTRICAL
54A-480
STEP 6. Check the harness wire between C-171
RV meter connector terminals No.10, 23 and A-36
ambient air temperature sensor connector
terminals No.2, 1.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connector C-33, and repair if necessary.
• Check the output lines for open circuit and short
circuit.
Q: Is the check result normal?
YES :
Go to Step 7
NO :
Repair the wiring harness.
STEP 7. Recheck for malfunction.
Q: Is a malfunction eliminated?
YES :
If no malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− How to Cope
with Intermittent Malfunction .
NO :
Go to Step 8
STEP 8. Replace the ambient air temperature
sensor temporarily, and check the trouble
symptom.
Q: Is a malfunction eliminated?
YES :
Replace the ambient air temperature
sensor.
NO :
Replace the RV meter.
AC903897
AB
Connector: A-36
Harness side
A-36 (B)
AC903856
Connectors: C-33, C-171 <LHD>
BB
C-33
C-171
C-33
Harness side
C-171 (GR)
AC903868
Connector: C-171 <RHD>
BQ
Harness side
C-171 (GR)
AC903865
Connector: C-33 <RHD>
AH
RV METER
CHASSIS ELECTRICAL
54A-481
Inspection Procedure 3: The ambient air temperature is not displayed normally. <Vehicles with auto
A/C>
CIRCUIT OPERATION
• For the vehicles with auto A/C, the RV meter
receives and displays the ambient temperature
information from the A/C-ECU by CAN communi-
cation. Also, the ambient temperature displayed
on the RV meter is corrected by the vehicle
speed of the vehicle speed sensor.
• If the function type is set as 3 or 4 by mistake, the
ambient temperature cannot be displayed.
COMMENTS ON TROUBLE SYMPTOM
When other indications are normal, the malfunction
of A/C-ECU or CAN bus line is considered.
PROBABLE CAUSES
• Malfunction of the A/C-ECU
• Malfunction of the CAN bus line
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Check the function type in the service
mode.
Check that the function type is set as 1 or 2 in the
service mode. (Refer to
Q: Is the check result satisfactory?
YES :
Go to Step 2
NO :
Set the function type again in the service
mode, and recheck the trouble symptom.
(Refer to
.)
STEP 2. Check the RV meter.
Check that the average vehicle speed and the aver-
age fuel consumption are displayed normally, and
check that the connection with the vehicle speed
sensor is normal.
Q: Is the check result satisfactory?
YES :
Go to Step 3
NO :
Perform the troubleshooting, Inspection
Procedure 2: "The drive information is not
displayed normally". (Refer to
STEP 3. M.U.T.-III CAN bus diagnostics
Use the M.U.T-III to diagnose the CAN bus lines.
Q: Is the check result satisfactory?
YES :
Go to Step 4
NO :
Repair the CAN bus lines (Refer to GROUP
54C, Diagnosis - Can Bus Diagnostics Table
). After diagnosing the CAN bus lines, go to
Step 4.
STEP 4. M.U.T-III other system diagnosis code.
Check whether the A/C-ECU diagnosis code is set.
Q: Is the diagnosis code set?
YES :
Diagnose A/C-ECU (Refer to GROUP 55B,
Troubleshooting ), and then go to Step 5.
NO :
Go to Step 5
STEP 5. Recheck for malfunction.
Q: Is a malfunction eliminated?
YES :
If no malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− How to Cope
with Intermittent Malfunction .
NO :
Replace the RV meter.
Inspection Procedure 4: The freeze mark does not illuminate or flash normally. The freeze warning
buzzer does not sound.
CIRCUIT OPERATION
If the ambient temperature of RV meter becomes
3
°C or lower when the ignition switch is turned ON,
the freeze mark flashes for 10 seconds on the RV
meter and the ETACS-ECU buzzer sounds at the
same time.
NOTE: If the destination setting is wrong, normal
operation is not possible because the threshold val-
ues of the freeze mark or freeze warning buzzer are
different.
RV METER
CHASSIS ELECTRICAL
54A-482
freeze warning operate
COMMENTS ON TROUBLE SYMPTOM
When other indications are normal, the malfunction
of RV meter or ETACS-ECU is considered.
PROBABLE CAUSES
• Malfunction of the RV meter
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Check the DESTINATION in the service
mode
Check that in the service mode the item "DESTINA-
TION" is set as "G
⋅EXP/EU/MMAL". (Refer to
.)
Q: Is the check result satisfactory?
YES :
Go to Step 2
NO :
Set the "DESTINATION" again in the
service mode, and recheck the trouble
symptom. (Refer to
.)
STEP 2. Check the RV meter.
Check that the ambient air temperature is displayed
normally.
Q: Is the check result satisfactory?
YES (The freeze mark does not illuminate or flash
normally.) :
Go to Step 5
YES (The freeze warning buzzer does not sound.) :
Go to Step 3
NO :
Perform the troubleshooting, Inspection
Procedure 2: "The drive information is not
displayed normally". (Refer to
STEP 3. M.U.T.-III CAN bus diagnostics
Use the M.U.T-III to diagnose the CAN bus lines.
Q: Is the check result satisfactory?
YES :
Go to Step 4
NO :
Repair the CAN bus lines (Refer to GROUP
54C, Diagnosis - Can Bus Diagnostics Table
). After diagnosing the CAN bus lines, go to
Step 4.
STEP 4. M.U.T-III other system diagnosis code.
Check that the ETACS-ECU does not set the diagno-
sis code.
Q: Is the diagnosis code set?
YES :
Diagnose ETACS-ECU (Refer to GROUP
54B, Diagnosis - diagnosis code chart ).
NO :
Go to Step 5
STEP 5. M.U.T.-III diagnosis code.
When the ignition switch is turned to the "LOCK"
(OFF) position, check that the RV meter does not set
the diagnosis code.
Q: Is the diagnosis code set?
YES :
Refer to diagnosis code chart
.
NO :
Go to Step 6
STEP 6. Recheck for malfunction.
Q: Is a malfunction eliminated?
YES :
If no malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− How to Cope
with Intermittent Malfunction .
NO :
Replace the RV meter.
Conditions
Display control
When the air temperature is 3
°C or lower, at the ignition
switch "ON" position.
The ETACS-ECU buzzer (freeze warning buzzer)
sounds and the freeze mark flashes for 10
seconds.
When the air temperature that is over 3
°C at the ignition
switch "ON" position changes to 3
°C or lower.
After the
warnings
described as
above is
operated.
When the air temperature that is 6
°C or
higher changes to 3
°C or lower
When the air temperature reaches to 6
°C, the
freeze mark disappears, and when the air
temperature decreases to 3
°C or lower again,
the freeze mark flashes for 10 seconds.
However, the buzzer does not sound.
When the air temperature that is over 3
°C but below 6 °C decreases to 3 °C or
lower
When the air temperature is over 3
°C but below
6
°C, the freeze mark keeps displaying. If the air
temperature decreases to 3
°C or lower again,
the buzzer does not sound and the freeze mark
does not flash again.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст