Mitsubishi L200. Manual — part 354
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-31
NOTE: The O-rings are mounted on the transmis-
sion case side as shown in the illustration. How-
ever there may be cases where they will come off
with the valve body.
AK601377AC
Snap ring
13.Remove the snap ring and disconnect the
solenoid valve harness.
AK601378AC
Oil strainer
Oil seal
14.Remove the oil strainer and two oil seals.
AK601921AC
4
3
2
1
AK601922 AC
6
5
15.Remove each accumulator piston, seal ring and
spring.
Remove the snap ring, then remove the
accumulator cover, O-ring and spring.
No.
Name
1
For overdrive clutch
2
For second brake
3
For low/reverse brake
4
For underdrive clutch
5
For reduction brake
6
For direct clutch
NOTE: To make assembly easier, attach an iden-
tification tag on the removed accumulator piston.
AK601923AC
Spring pin
16.Remove the detent lever spring pin.
AK601924AC
Pin
Parking roller
rod
Detent lever
Manual control
shaft
17.Remove the pin, and then remove the manual
control shaft, two O-rings, detent lever and
parking roller rod.
AK503505AB
18.Remove the eight converter housing mounting
bolts, and then converter housing.
AK601926AC
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-32
19.Remove the ten oil pump mounting bolts.
20.Install the special tool into the bolt hole shown in
the illustration.
AK601927AC
MD998333
21.While screwing in special tools Oil pump remover
(MD998333) evenly, remove the oil pump.
22.Remove the oil pump gasket.
AK601928AD
Thrust race No.1
Thrust bearing No.2
23.Remove the thrust race No.1 and thrust bearing
No.2.
NOTE: The thrust race No.1 may be attached to
the oil pump.
AK601929
24.Remove the reverse and overdrive clutch.
AK601930AD
Thrust bearing No.3
25.Remove the thrust bearing No.3.
AK601931
26.Remove the overdrive clutch hub.
AK601932AD
Thrust bearing No.4
27.Remove the thrust bearing No.4.
NOTE: The thrust bearing No.4 may be attached
to the overdrive clutch hub.
AB601933
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-33
28.Remove the reverse sun gear.
AK601934
29.Remove the snap ring.
AK601935
30.Remove the second brake.
AK601936
31.Remove the return spring.
AK601937
32.Remove the pressure plate, brake plates and
brake discs.
AK601938
33.Remove the low/reverse annulus gear.
AK601939AD
Thrust bearing No.7
34.Remove the thrust bearing No.7.
NOTE: The thrust bearing No.7 may be attached
to the low/reverse annulus gear.
AK601940
35.Remove the snap ring.
AK601941
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V5A5>
23D-34
36.Remove the reaction plate and one brake disc.
AK601942
37.Remove the snap ring.
AK601943
38.Remove the brake plates, brake discs, and
pressure plate.
AK601944
39.Remove the wave spring.
AK601945
40.Remove the snap ring.
AK601946
41.Remove the center support.
AK601947AD
Thrust race No.8
Thrust bearing No.9
42.Remove the thrust race No.8 and thrust bearing
No.9.
NOTE: The thrust race No.8 may be attached to
the center support.
AK601948
43.Remove the direct annulus gear.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст