Mitsubishi L200. Manual — part 551
MOULDINGS
EXTERIOR
51-20
MOULDINGS
ROOF DRIP MOULDING REMOVAL AND INSTALLATION
M1511004701771
ACA00434AB
Section A – A
Section B – B
Section C – C
Section D – D
A
B
B
B
B
B
A
A
A
D
D
D
D
C
C
C
C
8
N
8
N
8
N
7
N
7
N
7
N
B
A
9
N
9
N
9
N
2
2
2
Claw
Grommet
Screw
2
D
D
1
10
C
C
10
10
1
1
3
3
A
3
6
6
6
5
5
5
4
4
4
10
3,4,5,6
7,8,9
2
2
1
2
Double-sided tape: Generic
products, 10 mm width and
30 mm length
<Double cab>
<Single cab>
<Club cab>
Roof drip moulding removal steps
1. Rear end cover
<<
A
>> >>
A
<< 2. Roof drip moulding
3. Clip A (Yellow)
4. Clip A (Green)
5. Clip A (Dark blue)
6. Clip A (Red)
7. Clip B (Material colour)
8. Clip B (Light grey)
9. Clip B (Yellow)
10. Clip C
Roof drip moulding removal steps
MOULDINGS
EXTERIOR
51-21
REMOVAL SERVICE POINT
<<A>> ROOF DRIP MOULDING REMOVAL
AC303685
NOTE: Use a commercial ornament remover (resin-
made) as shown to pry out the roof drip moulding.
INSTALLATION SERVICE POINT
>>A<< ROOF DRIP MOULDING INSTALLATION
Install the clips to the roof drip moulding before
installing the moulding to the vehicle body.
DOOR PROTECT MOULDING REMOVAL AND INSTALLATION
AC509718
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AC
<Club cab>
<Double cab>
Section A – A
Boss
1
1
3
2
1,2,3
Door protect moulding removal
steps
<<
A
>> >>
A
<< 1. Front door protect moulding
<<
A
>> >>
A
<< 2. Rear pillar protect moulding
<<
A
>> >>
A
<< 3. Rear door protect moulding
AC509721
Double-sided tape: Generic products
AB
1
2, 3
Double-sided tape affixed location
MOULDINGS
EXTERIOR
51-22
REMOVAL SERVICE POINT
<<A>> DOOR AND REAR PILLAR PROTECT
MOULDINGS REMOVAL
Gently lift and remove the moulding. If there is any
double-sided tape remaining on the moulding,
remove it according to the following instructions.
<Remove double-sided tape remaining on the body
surface>
AC000420
Double-sided tape
Protection tape
AB
1. Attach protection tape all the way along the edges
of the double-sided tape which is still adhering to
the body.
AC000421
Double-sided tape
AB
2. Use a resin spatula to scrape off the double-sided
tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag
moistened with the parts cleaner (MZ100387 or
equivalent).
<Remove double-sided tape remaining on the
moulding and adhere double-sided tape (when re-
using a moulding)>
AC313343
1. Scrape off the double-sided tape on the moulding
with a resin spatula as possible.
2. Wipe the door moulding surface and clean it with
a rag moistened with the parts cleaner
(MZ100387 or equivalent).
3. Remove only a small portion of the residual
adhesive.
4. Adhere the double-sided tape as specified on the
moulding.
DOOR SASH TAPE <VEHICLES WITH WIDE FENDER>
EXTERIOR
51-23
INSTALLATION SERVICE POINT
>>A<< DOOR AND REAR PILLAR PROTECT
MOULDINGS INSTALLATION
AC313344
Backing paper
Adhesive tape
AB
1. Tear off the double-sided tape backing paper.
NOTE: If attach the adhesive tape to the edge of
the backing paper, it will be easy to tear off.
2. Install the clips to the moulding before installing it
to the vehicle body.
3. Install the mouldings.
NOTE: If the double-sided tape is difficult to affix
in cold temperature, etc., warm the bonding sur-
faces of the body and moulding to about 40
−
60
°
C
before affixing the tape.
4. Firmly press in the moulding onto the respective
body surface.
DOOR SASH TAPE <VEHICLES WITH WIDE FENDER>
SPECIAL TOOL
M1511000601664
Tool
Number
Name
Use
MB990528
MB990528
Stripe tape spatula Installation of door sash tape
LUBRICANT
M1511000400140
Item
Specified lubricant
Quantity
Degrease agent
Grease and dirt removal
from parts surface
Parts cleaner (MZ100387 or
equivalent)
As required
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст