Mitsubishi L200. Manual — part 780
RV METER
CHASSIS ELECTRICAL
54A-487
5. Press the [BACK] button to return to the
"COMPASS VARIANCE" screen.
HOW TO SET THE COMPASS CALIBRA-
TION
NOTE: Perform compass calibration in a space
where the vehicle can turn around, with the engine
running.
The "COMPASS SETTING" screen is displayed with
the user customisation function in the RV meter.
1. When the "COMPASS VARIANCE" screen is
displayed, press the [SELECT] button.
2. Press the [
←] button or the [→] button.
3. When the "COMPASS CALIBRATION" screen is
displayed, press the [SELECT] button.
4. When "CALIBRATION READY?" is indicated,
press the [SELECT] button.
5. When "PLEASE DRIVE SLOWLY IN A SAFE,
OPEN AREA" is indicated, turn the vehicle 360
° in
a safe and open area.
6. "COMPASS CALIBRATION COMPLETE" is
indicated with a blip, and the compass calibration
is completed. When three seconds have elapsed
after completion, the information screen is
displayed.
AC900073
AC900073
AC900074
AC900075
AC900078
AC900079
RV METER
CHASSIS ELECTRICAL
54A-488
NOTE:
.
•
When the engine is stopped during compass calibra-
tion, "PLEASE START ENGINE" is displayed.
Perform compass calibration with the engine run-
ning.
•
If the compass sensor is not normal during compass
calibration, "COMPASS SENSOR ERROR" is
displayed. In this case, perform RV meter trouble-
shooting "The compass does not indicate nor-
mally". (Refer to
.)
VEHICLE MAGNETIC COMPENSATION
M1543009700288
DEMAGNETIZATION AND CORRECTION
METHOD
CAUTION
• If the tip of demagnetizer touches the roof
panel, the magnetising condition of body
becomes worse to the contrary. Absolutely
avoid this.
• If the demagnetizer is turned OFF near the
body or it is suddenly separated from the
body, the magnetising condition of body
becomes worse to the contrary. Absolutely
avoid these.
1. Turn the ignition switch to the OFF position.
2. Demagnetize the body using a commercial
demagnetizer.
3. While keeping the distance between the tip of
demagnetizer and the roof panel to approximately
50 mm, move the demagnetizer slowly with a
sweeping manner on the rear-half surface of roof
panel.
4. Slowly draw the demagnetizer apart from the
body. Turn OFF the switch of demagnetizer when
it is apart from the body more than 50 mm.
5. After demagnetization of the geomagnetism,
perform a compass calibration (Refer to How to
Set the Compass
AC900077
AC900076
AC001246AB
Commercial demagnetizer
AC900188
Front
Demagnetizer
Approximately 50 mm
Roof panel
AB
RV METER
CHASSIS ELECTRICAL
54A-489
RV METER
REMOVAL AND INSTALLATION
M1543014100077
CAUTION
• When the RV meter of another vehicle is replaced, perform "BODY TYPE" and "FUNCTION TYPE
RESET" in the service mode. (Refer to
• After replacement of the RV meter, when the ignition switch is turned to the "ON" position for the
first time, "BODY TYPE" and "DESTINATION" of the service mode are displayed automatically. Set
each item following the description of the service mode. (Refer to
.) Also perform the
deviation angle correction. (Refer to
AMBIENT AIR TEMPERATURE
SENSOR
REMOVAL AND INSTALLATION
M1543032700042
INSPECTION
AMBIENT AIR TEMPERATURE SENSOR
INSPECTION
M1546602600054
Check to see that the resistance shown in the graph
is almost satisfied when measuring the resistance
between the sensor terminals under two or more dif-
ferent temperature conditions.
AC900684
1
2
2
3
AB
Removal steps
•
RV meter hood (Refer to GROUP
52A
− Instrument Panel Assembly
)
1.
RV meter assembly
2.
RV meter bracket
3.
RV meter
AC501630
AC
1
Removal steps
•
radiator grille (RH) (GROUP 51,
Radiator grille .)
1.
Ambient air temperature sensor
AC209192AB
10
8
6
4
2
0
10
20
30
40
–10
0
RESISTANCE
(k )
TEMPERATURE (˚C)
DEFOGGER
CHASSIS ELECTRICAL
54A-490
DEFOGGER
TROUBLESHOOTING
M1540500200033
Refer to GROUP 55A, Troubleshooting .
INSPECTION
PRINTED HEATER LINES CHECK
M1540500500368
1. Run engine at 2,000 r/min. Check heater element
with battery at full.
2. Turn "ON" rear window defogger switch. Measure
heater element voltage with circuit tester at rear
window glass centre A. Condition is good if it
indicates about six volts.
3. If 12 volts is indicated at A, there is a break in the
negative terminals from A. Move test bar slowly to
negative terminal to detect where voltage
changes suddenly (0 volts).
4. If 0 volts is indicated at A, there is a break in the
positive terminals from A. Defect where the
voltage changes suddenly (12 volts) in the same
method described above.
5. If a malfunction such as open circuit occurs,
replace the rear window glass <vehicles without
rear panel power window> or rear slide window
glass <vehicles with rear panel power window>.
(Refer to GROUP 42, Rear window glass <rear
window glass>, Rear panel power window <rear
slide window glass>.)
AC002357AI
A
AC407247
Voltage (V)
Voltage (V)
12
6
12
6
Open circuit point
AC
Normal characteristic curve
A (Centre point)
Approximately 6 V
Positive
terminal
Negative
terminal
Print heater line
Positive
terminal
Negative
terminal
Print heater line
Abnormal characteristic curve
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст