Mitsubishi L200. Manual — part 370
25-1
GROUP 25
PROPELLER SHAFT
CONTENTS
GENERAL INFORMATION . . . . . . . .
SERVICE SPECIFICATION(S) . . . . .
LUBRICANT(S) . . . . . . . . . . . . . . . . .
SPECIAL TOOL(S) . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
PROPELLER SHAFT UNIVERSAL JOINT CHECK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROPELLER SHAFT . . . . . . . . . . . . .
PROPELLER SHAFT REMOVAL AND INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROPELLER SHAFT INSPECTION . . . . . .
PROPELLER SHAFT DISASSEMBLY AND
REASSEMBLY . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION
PROPELLER SHAFT
25-2
GENERAL INFORMATION
M1251000100562
<2WD>
• A 2 way split 3-joint type propeller shaft with cen-
tre bearing is adopted.
• A snap ring method of securing the journal bear-
ing for the universal joint is adopted.
<4WD>
• A 2-joint type propeller shaft for front propeller
shaft, a 2 way split 3-joint type propeller shaft with
centre bearing for rear propeller shaft are
adopted. <Vehicles with Easy select 4WD-M/T>
• A 2-joint type propeller shaft for front propeller
shaft, a 2-joint type propeller shaft for rear propel-
ler shaft are adopted. <Vehicles with Easy select
4WD-A/T, Vehicles with Super select 4WD>
• A snap ring method of securing the journal bear-
ing for the universal joint is adopted.
• BJ is adopted for front propeller shaft. <Vehicles
with Super select 4WD>
NOTE: BJ: Birfield Joint
CONSTRUCTION DIAGRAM
AC407335
Centre bearing assembly
Rear propeller shaft
assembly
AC
Front propeller shaft
assembly
<2WD (except High rider)>
AC607601AE
<2WD (High rider)>
Centre bearing assembly
Rear propeller shaft
Front propeller shaft
AC407336
Centre bearing assembly
Rear propeller shaft
(Rear)
AC
Front propeller shaft
assembly
Rear propeller shaft
(Front)
<Vehicles with
Easy select 4WD-M/T>
AC407337
Rear propeller shaft assembly
AE
Front propeller shaft assembly
<Vehicles with
Easy select 4WD-A/T>
AC510097
Rear propeller shaft assembly
AB
Front propeller
shaft assembly
<Vehicles with
Super select 4WD>
BJ
SERVICE SPECIFICATIONS
PROPELLER SHAFT
25-3
SERVICE SPECIFICATIONS
M1251000300265
Item
Standard value
Limit
Propeller shaft run-out mm
−
0.6
Clearance between snap ring and snap ring groove mm
0.06 or less
−
LUBRICANT
M1251000400347
Item
Specified lubricant
Quantity
Sleeve yoke
Gear oil API classification GL-3 SAE 75W-85 As required
SPECIAL TOOLS
PROPELLER SHAFT
25-4
SPECIAL TOOLS
M1251000600266
Tool
Number
Name
Use
MB990810
MB990810
Side bearing puller
Centre bearing removal
MB990840
MB990840
Universal joint remover
and installer
Disassembly and
reassembly of universal
joint
MB991410
MB991410
Collar
ON-VEHICLE SERVICE
PROPELLER SHAFT UNIVERSAL JOINT
CHECK
M1251002400086
PROPELLER SHAFT VISUAL CHECK
1. Place the gearshift lever to the "N" (neutral
position) <M/T> or the selector lever to the "N"
position <A/T>.
2. Then place the transfer shift lever to the "2WD"
position. <4WD>
3. Check the propeller shaft for dent, damage or
crack.
AC808283
AB
<Correct state>
Oil seal
AC510591AB
Oil seal lip
protruded
<Incorrect
state>
4. Check the propeller shaft universal joint, oil seal
for crack or damage. If abnormality is recognized,
replace the universal joint with a new one.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст