Mitsubishi L200. Manual — part 491
Removal steps
<<
A
>> >>
B
<< 1. Rear window glass
>>
A
<< 2. Window dam
>>
A
<< 3. Glass stopper
>>
A
<< 4. Fastener
WINDOW GLASS
BODY
42-24
REMOVAL SERVICE POINT
<<A>> REAR WINDOW GLASS REMOVAL
Remove the rear window glass in the same proce-
dure as for the windshield glass removal (Refer to
INSTALLATION SERVICE POINTS
>>A<< FASTENER/GLASS STOPPER/WINDOW
DAM INSTALLATION
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
1. Use the parts cleaner (MZ100387 or equivalent)
to degrease the inside and outside edges of the
rear window glass and the surface of the body
flange.
AC502951
AC502508
AC502509
AC502510
AC
Fastener
Glass stopper
Seal line
Ceramic line
Ceramic line
Rear window
glass end line
Fastener and glass stopper installation positions
Align the glass stopper end line
with the rear window glass mark.
Align the fastener end line with
the rear window glass mark.
Seal line
Rear window glass
21.7 ± 0.5 mm
15.6 ± 1 mm
Rear window
glass end line
2. Install the fasteners and glass stoppers to the
specified positions of the rear window glass.
AC502511
AB
Fastener
Attach the fastener in
alignment with the notches
Notch on the body flange
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-25
3. Install the fasteners to the left and right lower
corner of the body flange.
4. Install the window dam.
>>B<< REAR WINDOW GLASS INSTALLATION
Install the rear window glass in the same way as for
the windshield glass installation (Refer to
REAR PANEL POWER WINDOW <Vehicles with rear panel
power window>
GENERAL INFORMATION
M1421000100701
REAR PANEL POWER WINDOW
AC901885AB
Rear panel power
window motor
Rear panel power
window regulator
Rear slide window glass
Rear side window glass
Rear side window glass
Rear window panel
Rear panel power
window ECU
Rear panel power window switch
A rear panel power window has been installed in the
double cab to improve open airy feeling and ventila-
tion performance <Vehicles with rear panel power
window>. The rear panel power window has the fol-
lowing features.
• The anti-trapping function is adopted.
• The power window timer function is adopted.
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-26
DESCRIPTION OF STRUCTURE AND
OPERATION
REAR PANEL POWER WINDOW FUNCTION
•
AC501245
AB
Rear slide window glass
Fully open
position
Fully close
position
Ventilation position
As for the rear panel power window, the rear slide
window glass moves in 3 levels by operating the
rear power window switch.
•
AC901886AB
Section A – A
Rear panel power window switch
Fully close
Off
Fully open
Ventilation
close
A
A
Ventilation
open
The rear panel power window switch employs the
push operation method to improve safety. To
open a rear slide window glass, press in the
switch knob lower side, and to close, press in the
upper side.
• The one-touch mechanism is adopted to the rear
panel power window switch to fully open or close
rear slide window glass in a single operation.
ANTI-TRAPPING FUNCTION
The rear panel power window with the safety mecha-
nism is adopted. If any obstacle such as a hand or a
head is detected to be trapped during a window
glass closing operation, the window glass is opened
by approximately 150 mm to improve safety.
NOTE: If anti-trapping function is activated consecu-
tively three times or more, the fully closed position
that power window switch has learned will be erased.
With this state, auto-up/down function becomes inef-
fective. To make the rear panel power window switch
learn the fully closed position, the initialisation is
required. Refer to
.
REAR PANEL POWER WINDOW TIMER
FUNCTION
AC501237
Ignition switch (IG1)
ON
(Open)ON
ON
t
OFF
t: 30 seconds
(Close)OFF
OFF
Driver's door
switch
Power window relay
AC
The rear panel power window can be opened or
closed by a timer function after the ignition switch is
turned to the OFF position (The timer delay is
extended for 30 seconds if the driver’s door is
opened while the timer is on. The timer operation,
however, is cancelled when the driver’s door is
closed before the timer ends).
SEALANTS
M1429000500059
Item
Specified sealant
Rear side window glass assembly
3M ATD Part No.3509 or equivalent
Waterproof film
3M ATD Part No.8625 or equivalent
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-27
SPECIAL TOOLS
M1429000600078
Tool
Number
Name
Use
MB990480
MB990480
Window glass holder
Removal of rear panel window
regulator
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст