Mitsubishi L200. Manual — part 484
POWER STEERING OIL PUMP ASSEMBLY
POWER STEERING
37-39
REASSEMBLY SERVICE POINTS
>>A<< O-RING INSTALLATION
AC502155AC
1
2
No.
ID
× Width mm
1
17.8
× 2.4
2
13.5
× 1.5
>>B<< OIL SEAL INSTALLATION
AC000752
MB990938
AB
MB991203
Use following special tool to install the oil seal.
• Bar (MB990938)
• Oil seal and bearing installer (MB991203)
>>C<< CAM RING INSTALLATION
CAUTION
Be sure to install the cam ring in the correct
direction as shown.
AC100171AB
Side plate side
Pump cover side
Install the cam ring as shown in the illustration.
INSPECTION
M1372005500329
• Check the flow control valve of the pump body for
clogging.
• Check the pulley and shaft for wear or damage.
• Check the rotor and vane groove for "stepped"
wear.
• Check the contact surface of cam ring and vanes
for "stepped" wear.
• Check the vanes for damage.
POWER STEERING HOSES
POWER STEERING
37-40
POWER STEERING HOSES
REMOVAL AND INSTALLATION
M1372005702426
Pre-removal and Post-installation Operation
• Power Steering Fluid Draining and Refilling (Refer to
) and Bleeding (Refer to
AC712001
15 ± 2 N·m
45 ± 4 N·m
12 ± 2 N·m
57 ± 7 N·m
4
11
6
9
7
8
AE
12
15 ± 2 N·m
10
13
14
<LHD>
12 ± 2 N·m
5
12 ± 2 N·m
12 ± 2 N·m
2
3
1
AC501430
15 ± 2 N·m
45 ± 4 N·m
12 ± 2 N·m
12 ± 2 N·m
57 ± 7 N·m
5
2
4
11
6
9
7
8
AO
12
15 ± 2 N·m
10
13
14
12 ± 2 N·m
<RHD>
3
1
12 ± 2 N·m
Removal steps
1.
Cap
2.
Oil reservoir
3.
O-ring
>>
E
<< 4.
Return hose
>>
D
<< 5.
Suction hose
6.
Eye bolt
7.
Gasket
>>
C
<< 8.
Pressure hose assembly
>>
A
<< 9.
Pressure tube assembly
10.
O-ring
11.
Return tube assembly
>>
B
<< 12.
Return hose
>>
A
<< 13.
Return tube assembly
14.
O-ring
POWER STEERING HOSES
POWER STEERING
37-41
INSTALLATION SERVICE POINTS
>>A<< RETURN TUBE ASSEMBLY/PRESSURE
TUBE ASSEMBLY INSTALLATION
AC407280 AB
Mating marks
Align the mating marks on the gear box, return tube
assembly and pressure tube assembly when install-
ing.
POWER STEERING HOSES
POWER STEERING
37-42
>>B<< RETURN HOSE INSTALLATION
AC511312
AD
Mating marks
Return hose
Return tube
assembly
<2WD(except High rider)
-LHD>
AC509070AI
Mating
marks
Return tube
assembly
Return hose,
Return hose B
<2WD(High rider),
4WD-LHD>
AC501540
AO
Mating
marks
Return hose
Return tube
assembly
<2WD(High rider),
4WD-RHD>
1. Install the return hose and return tube assembly
so that the mating marks and facing forward
<Except 2WD (High rider), 4WD-RHD>, or
upward <2WD (High rider), 4WD-RHD>.
AC511314
AD
Return tube
assembly
Return hose
<2WD(except High rider)-LHD>
Mating marks
AC509069
AF
Return tube
assembly
Return hose
<2WD(High rider),4WD-LHD>
Mating marks
AC501544
AM
Return tube
assembly
Return hose
Mating marks
<2WD(High rider),4WD-RHD>
2. Install so that the mating marks are faced forward.
>>C<< PRESSURE HOSE ASSEMBLY
INSTALLATION
AC501546
AB
Mating
marks
1. Install so that the mating marks are facing
rearward.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст