Mitsubishi Lancer Evolution 7. Manual — part 274
PROPELLER SHAFT - Propeller Shaft
25-9
4. Apply a little specific sealant to the surface which has
groove (for packing) of LJ assembly (allow as shown
in the illustration), fix the rubber packing.
Specified sealant: 3M Stud Locking 4170 or equivalent
5. Install the surface which has groove (for packing) of LJ
assembly to LJ boot side.
6. Aline the mating marks of LJ assembly and center propeller
shaft, then punch the LJ assembly to center propeller shaft
using socket wrench.
7. Aline the position of bolt holes of LJ boot and LJ assembly,
install the LJ boot to LJ assembly.
8. Fix the rubber packing of companion flange side in a
similar to step 4.
"
CA BOOT BAND INSTALLATION
Caution
1. Tighten the boot band part in opposite direction of
convex part for bleeding the boot.
2. If there is grease in the convex part, wipe out the
grease in order to bleed the boot.
Rubber packing
LJ assembly
Socket wrench
Bolt
LJ boot
Boot band Installation position
Projection
Boot
PROPELLER SHAFT - Propeller Shaft
25-10
"
DA CENTER BEARING ASSEMBLY/COMPANION
FLANGE/SELF LOCKING NUT INSTALLATION
1. Install the center bearing assembly to the rear propeller
shaft in the direction shown as the illustration.
2. After alining the mating marks of the companion flange
and rear propeller shaft, install them.
3. Tightening the self locking nut, press fit the center bearing
assembly using companion flange.
Center propeller shaft rear side
Companion
flange
Self
locking
nut
Center bearing
assembly
Dust seal
Rubber
mount
Center propeller shaft front side
Companion
flange
Self
locking
nut
26-1
FRONT AXLE
CONTENTS
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
Wheel Bearing Axial Play Check
FRONT AXLE -
General Information
26-2
GENERAL INFORMATION
The front axle consists of front hubs, knuckles,
wheel bearings and drive shafts, and it has the
following features.
D
The wheel beearing is unit bearing integrated
with hub (Double-row angular contact ball
bearing).
D
The drive shaft incorporates B.J.-T.J. type
constant velocity joints with high transmission
efficiency and low vibration and noise.
D
ABS rotors for detecting the wheel speeds are
press-fitted to the B.J. outer wheels in vehicles
with ABS or ACD.
NOTE
1. B.J.: Birfield Joint
2. T.J.: Tripod Joint
SPECIFICATIONS
Item
Specifications
Wheel
bearings
Wheel bearing type
Hub unit bearing (Double-row angular
contact ball bearing)
g
Bearing (outside diameter) mm
87*
1
Drive
shaft
Joint type
Outside
B.J.
shaft
Inside
T.J.
Shaft length*
2
× Shaft diameter mm
Left
350 × 26
Right
427 × 26
NOTE
*
1
: The wheel beearing is integrated with hub, only the outer diameter is shown.
*
2
: The shaft length indicates the length between the center points of each joint.
STRUCTURAL DIAGRAM
B.J.
T.J.
Knuckle
Output shaft
Strut assembly
Drive shaft
Wheel bearing
Front hub
T.J. (L.H.)
Output shaft
T.J. (R.H.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст