Mitsubishi Lancer Evolution 7. Manual — part 276
FRONT AXLE -
Hub and Knuckle Assembly
26-7
REMOVAL SERVICE POINTS
A
A" CALIPER ASSEMBLY REMOVAL
Secure the removed caliper assembly with wire, etc.
Caution
If the vehicle is equipped with the Brembo disc brake,
during maintenance, take care not to contact the parts
or tools to the caliper because the paint of caliper will
be scratched. And if there is brake fluid on the caliper,
wipe out quickly.
A
B" CASTLE NUT REMOVAL
Caution
Do not apply the vehicle weight to the wheel bearing
while loosening the castle nut. Otherwise wheel bearing
will be damaged.
A
C" TIE ROD END DISCONNECTION
Caution
1. Loosen the nut only; do not remove it from the ball
joint. Otherwise ball joint thread will be damaged.
2. The special tool should be suspended by a cord to
prevent it from coming off.
A
D" DRIVE SHAFT REMOVAL
1. Use the special tools to push out the drive shaft from
the hub.
2. Withdraw the drive shaft from the hub by pulling the bottom
of the brake disc towards you, and then remove the hub
retaining bolts.
MB990767
Nut
Cord
Ball joint
MB991113
or
MB990635
MB990242
MB990767
MB991354
MB990244
(Three)
FRONT AXLE -
Hub and Knuckle Assembly
26-8
INSTALLATION SERVICE POINT
"
AACASTLE NUT INSTALLATION
1. Be sure to install the castle nut washer in the specified
direction.
2. Using the special tool, tighten the castle nut.
Caution
Before securely tightening the castle nuts, make sure
there is no load on the wheel bearings. Otherwise
wheel bearing will be damaged.
INSPECTION
INSPECTION OF WHELL BEARING ROTATION STARTING
TORQUE
1. Tighten special tools in hub and knuckle assembly to
the specified torque.
2. Measure the wheel bearing rotation starting torque with
special tools.
Limit: 1.03 N·m or less
3. Wheel bearing rotation starting torque must be under
the limit value and there should be no roughness when
rotating the hub.
WHEEL BEARING AXLE PLAY CHECK
1. Secure knuckle in a vice to measure axle play in wheel
bearing.
Limit: 0.06 mm
2. If the limit value of wheel bearing axle plya cannot be
obtained when tightened to the specified torque (245
± 29 N·m), check mounting bolt for hub and knuckle
assembly. If no defects are found, replace hub assembly.
MB990767
245±29 N·m
Washer
MB991000
(MB990998)
Bolt
245±29 N·m
Secure bolt and
tighten nut.
MB991017
MB990326
MB990685
MB991000
(MB990998)
245±29 N·m
Secure bolt and
tighten nut.
MB991017
FRONT AXLE -
Hub and Knuckle Assembly
26-9
DISASSEMBLY AND REASSEMBLY
2
1
88 ± 10 N·m
Disassembly steps
1. Knuckle
2. Front hub assembly
FRONT AXLE -
Drive Shaft
26-10
DRIVE SHAFT
REMOVAL AND INSTALLATION
Caution
1. If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to
contact the parts or tools to the caliper because the paint of caliper will be scratched. And
if there is brake fluid on the caliper, wipe out quickly.
2. For vehicles with ABS or ACD, do not strike the rotor for wheel speed sensor installed to
the B.J. outer race of drive shaft against other parts when removing or installing the drive
shaft. Otherwise the rotor for wheel speed sensor will be damaged.
Pre-removal and Post-installation Operation
D
Transmission Fluid Draining
D
Transfer Oil Draining (Refer to GROUP 22 –
On-vehicle Service.)
Pre-removal and Post-installation Operation
D
Check the Dust Cover for cracks or damage by
pushing it with finger.
D
Transfer Oil Filling (Refer to GROUP 22 –
On-vehicle Service.)
D
Transmission Fluid Filling
1
6
9
8
5
7
4
3
2
11
25 ± 4 N m
25 ± 5 N m
245 ± 29 N m
108 ± 10 N m
10
11
39 ± 5 N m
Removal steps
1. Split pin
"
BA 2. Castle nut
3. Front speed sensor <Vehicles with
ABS or ACD>
4. Front speed sensor harness brack-
et
5. Brake hose bracket
6. Stabilizer bar link connection
7. Lower arm ball joint connection
A
A"
8. Tie rod end connection
A
B" "AA 9. Drive shaft
A
C" "AA 10. Output shaft
11. Circlip
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст