Mitsubishi Lancer Evolution 7. Manual — part 350
EXTERIOR -
Windshield Wiper and Washer
51-17
INSPECTIONS
WINDSHIELD WIPER MOTOR CHECK
Inspection of windshield wiper motor is conducted by removing
the harness connector with the motor attached to the vehicle.
D
Operation inspection of windshield wiper motor
rotation in a low or high speed
Connect the battery to the windshield wiper motor to
inspect the operation of motor rotation in a low or high
speed.
D
Inspection of windshield wiper motor stop position
(1) Connect the battery to the windshield wiper motor
to rotate the motor in a low speed as shown in the
illustration (A) and disconnect the battery during
rotation to stop the motor.
(2) Connect between the terminals and the battery as
shown in the illustration (B) and confirm whether the
motor stops at the automatic stop position after
rotating in a low speed.
FRONT WASHER MOTOR CHECK
(1) The inspection of front washer motor is conducted with
the washer hose connected after removing the washer
tank assembly and pouring water in the washer tank.
(2) Check that the water is supplied with strong pressure
after energizing terminal number 2 with battery voltage
and earthing terminal number 1.
(B) Automatical stop
Operation inspection
Low speed
High speed
Stop position inspection
(A) Low speed
EXTERIOR -
Windshield Wiper and Washer
51-18
WINDSHIELD WASHER NOZZLE INJECTION POSITION
CHECK
Move the nozzle to adjust the position so that the injection
can be done in an area shown in the illustration.
Caution
On R.H. drive vehicles, the illustration is symmetrical.
100
200
50
50
50
50
90
220
35
75
25
85
600
310
180
340
170
Windshield washer
nozzle perpendicular
Windshield washer
nozzle perpendicular
Ceramic line terminal
Windshield washer nozzle
<Right>
<Left>
Unit:mm
EXTERIOR -
Windshield Wiper and Washer
51-19
WINDSHIELD WIPER AND WINDSHIELD WASHER
SWITCH AND WINDSHIELD INTERMITTENT WIPER
INTERVAL ADJUSTING KNOB CHECK
<L.H.drive vehicles>
(1) Windshield wiper and washer switch, rear wiper and
washer switch.
Switch position
Terminal No.
p
6
7
8
9
10
11
6
7
8
9
10
11
OFF
Windshield wiper mist switch ON
Windshield intermittent wiper switch ON
Windshield low-speed wiper switch ON
Windshield high-speed wiper switch ON
Windshield washer switch ON
(2) Windshield intermittent wiper interval adjusting knob
Measure the resistance value at terminal numbers 3 and
6. The resistance value should rise smoothly from
approximately 0 Ω (“FAST” position) to apporoximately
1 kΩ (“SLOW” position).
WINDSHIELD INTERMITTENT WIPER INTERVAL
ADJUSTING KNOB CHECK
<R.H.drive vehicles>
Measure the resistance value at terminal numbers 4 and
6. The resistance value should rise smoothly from
approximately 0 W (“FAST” position) to approximately 1 kW
(“SLOW” position).
NOTE
The windshield washer switch and windshield wiper switch
is integrated in the column-ECU, so can not be checked as
an individual part. However, its operation can be checked
by the input signal check. (GROUP 54B - Troubleshooting.)
EXTERIOR -
Marks
51-20
MARKS
REMOVAL AND INSTALLATION
2
3
4
5
1
1. Three-diamond mark
"
AA 2. Three-diamond mark
"
AA 3. Evolution-VII mark
"
AA 4. LANCER mark
"
AA 5. RECARO decal <RS-II>
INSTALLATION SERVICE POINT
"
AA ATTACHMENT OF EACH MARK
1. ATTACHED POSITION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст