Mitsubishi Lancer Evolution 7. Manual — part 240
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21A-1
CLUTCH
CONTENTS
21A-2
CLUTCH
CONTENTS
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
Clutch Pedal Inspection and Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Pedal Position Switch Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH -
General Information/Service Specifications/Lubricants/On-vehicle Service
21A-3
GENERAL INFORMATION
The clutch is a dry single-disc, diaphragm type;
hydraulic pressure is used for the clutch control.
SERVICE SPECIFICATIONS
Items
Standard value
Clutch pedal height mm
202.1 - 206.1 <L.H. drive vehicles>
173.5 - 177.5 <R.H. drive vehicles>
Clutch pedal clevis pin play mm
1 - 3
Clutch pedal free play mm
4 - 13
Distance between the clutch pedal and the toeboard
when the clutch is disengaged mm
114.3 or more <L.H. drive vehicles>
100 or more <R.H. drive vehicles>
LUBRICANTS
Items
Specified lubricants
Quantity
Clutch fluid
Brake fluid DOT3 or DOT4
As required
Push rod assembly
Rubber grease
Boot
Release cylinder push rod
MITSUBISHI genuine grease Part No.
0101011
ON-VEHICLE SERVICE
CLUTCH PEDAL INSPECTION AND
ADJUSTMENT
1. Turn up the carpet, etc. under the clutch pedal.
2. Measure the clutch pedal height and the clutch pedal
clevis pin play.
Standard value (A):
202.1 - 206.1 mm <L.H. drive vehicles>
173.5 - 177.5 mm <R.H. drive vehicles>
Standard value (B): 1 - 3 mm
Clutch pedal height
<L.H. drive Vehicles>
A
A
<R.H. drive Vehicles>
Clutch pedal
stopper
Clutch pedal clevis pin play
B
CLUTCH -
On-Vehicle Service
21A-4
3. If the height of the clutch pedal is outside the standard
value, loosen the setting nut to adjust the pedal height
to the standard value.
Caution
Do not push in the master cylinder push rod at this
time, otherwise the clutch will not operate properly.
4. After completing the adjustments, confirm that the clutch
pedal free play (measured at the face of the pedal pad)
and the distance between the clutch pedal (the face of
the pedal pad) and the clutch pedal stopper or toeboard
when the clutch is disengaged are within the standard
value ranges.
Standard value (C): 4 - 13 mm
Standard value (D):
114.3 mm or more <L.H. drive vehicles>
100 mm or more <R.H. drive vehicles>
5. If the clutch pedal free play and the distance between
the clutch pedal and the clutch pedal stopper or toeboard
when the clutch is disengaged do not agree with the
standard values, it is probably the result of either air in
the hydraulic system or a faulty master cylinder, clutch
cylinder or clutch. Bleed the air, or disassemble and inspect
the master cylinder, clutch cylinder or clutch.
6. Turn back the carpet, etc.
BLEEDING
Specified fluid: Brake fluid DOT 3 or DOT 4
Caution
Use the specified brake fluid. Avoid using a mixture
of the specified fluid and other fluid.
CLUTCH PEDAL POSITION SWITCH
ADJUSTMENT
1. Adjust the clutch pedal. (Refer to P. 21A-3).
2. Disconnect the connector from clutch pedal position
switch.
3. Loosen the clutch pedal position switch by rotating approx.
quarter turn to counterclockwise.
4. Fix the clutch pedal in full stroke.
Clutch pedal
Setting nut
13 ± 2 N·m
Clutch pedal clevis pin play
C
<L.H. drive Vehicles> <R.H. drive Vehicles>
Clutch
pedal
stopper
D
D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст