Mitsubishi Lancer Evolution 7. Manual — part 241
CLUTCH -
On-Vehicle Service/Clutch Pedal
21A-5
5. Fix the clutch pedal position switch by rotating approx.
quarter turn to clockwise in the position as shown in the
illustration.
6. Connect the connector to the clutch pedal position switch.
7. Check that the engine starts when the clutch is released.
CLUTCH PEDAL
REMOVAL AND INSTALLATION
Post-installation Operation
D
Clutch Pedal Adjustment (Refer to P.21A-2.)
D
Clutch Pedal Position Switch Adjustment (Refer to
P.21A-4.)
6
7
13 ± 2 N·m
<L.H. drive vehicles>
<R.H. drive vehicles>
1
12 ± 2 N·m
8
11
2
4
5
9
12 ± 2 N·m
6
7
13 ± 2 N·m
10
8
12
13
3
14
5
9
10
11
12
13
14
Full stroke
position of
clutch pedal
Approx.
3.5 mm
CLUTCH -
Clutch Pedal
21A-6
Removal steps
D
Column cover, under cover, lower
frame (Refer to GROUP 52A.)
1. Connector connection
2. Clutch pedal position switch
3. Clutch pedal position switch sub-har-
ness
4. Clip
5. Stopper
6. Snap pin
7. Clevis pin
8. Clutch master cylinder mounting nut
9. Master cylinder member mounting bolt
10. Pedal pad
11. Pedal stopper
12. Clutch pedal assembly
13. Turn over spring
14. Bushing
INSPECTION
CLUTCH PEDAL POSITION SWITCH CONTINUITY
CHECK
1. Connect the circuit tester (Ω range) to the connector of
clutch pedal position switch.
2. When the shaft is pushed more than the dimension as
shown in the illustration if there is not continuity, and
removing if there is continuity, the switch is good condition.
Continuity
2.5 ± 1 mm
No continuity
CLUTCH -
Clutch Control
21A-7
CLUTCH CONTROL
REMOVAL AND INSTALLATION
Pre-removal Operation
Clutch Fluid Draining
Post-installation Operation
D
Clutch Fluid Supplying
D
Clutch Pedal Adjustment (Refer to P.21A-3.)
D
Clutch Pedal Position Switch Adjustment (Refer to
P.21A-4.)
D
Clutch Line Bleeding (Refer to P.21A-4.)
<L.H. drive vehicles>
7
6
11
4
9
5
2
1
3
10
15 ± 1 N·m
30 ± 4 N·m
13 ± 2 N·m
12 ± 2 N·m
18 ± 3 N·m
10
8
Specified grease:
MITSUBISHI genuine grease
Part No. 0101011
Release cylinder
push rod
Release fork
11
Clutch master cylinder removal
steps
1. Clevis pin assembly
2. Eye bolt
3. Gasket
4. Reservoir hose
5. Clevis pin and pushrod assembly con-
necting part
6. Clutch master cylinder
7. Sealer
8. Retainer assembly
Clutch release cylinder removal
steps
10. Clutch pipe
11. Clutch release cylinder
Clutch line removal steps
9. Clutch hose
10. Clutch pipe
CLUTCH -
Clutch Control
21A-8
<R.H. drive vehicles>
1
2
3
4
5
9
7
8
6
15 ± 1 N·m
13 ± 2 N·m
18 ± 3 N·m
6, 8
Specified grease:
MITSUBISHI genuine grease
Part No. 0101011
Release cylinder
push rod
Release fork
7
Clutch master cylinder removal
steps
1. Clevis pin assembly
2. Clutch pipe connection
3. Reservoir hose
4. Clutch master cylinder
5. Sealer
Clutch release cylinder removal
steps
6. Clutch pipe
7. Clutch release cylinder
Clutch line removal steps
8. Clutch pipe
9. Clutch hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст