Mitsubishi Evolution X. Manual — part 833
SIDE AIR DAM
TSB Revision
EXTERIOR
51-15
(1) Attach protection tape all the way along the edges of the
double-sided tape which is still adhering to the body.
(2) Scrape off the double-sided tape with a resin spatula as
possible.
(3) Peel off the protection tape.
(4) Use a shop towel moistened with 3M
™ AAD Part number
8906 or equivalent to wipe the body.
2. Remove double-sided tape remaining on side air dam and
adhere double-sided tape (when re-using side air dam).
(1) Scrape off the double-sided tape on the side air dam with
a resin spatula as much as possible.
(2) Wipe the side air dam surface and clean it with a rag
moistened with isopropyl alcohol.
(3) Remove only a small amount of the residual adhesive.
(4) Apply the primer as specified on the residual adhesive.
(5) Adhere the double-sided tape as specified on the side air
dam.
INSTALLATION SERVICE POINT
.
>>A<< SIDE AIR DAM INSTALLATION
1. Tear off the double-sided tape backing paper.
NOTE: Attach the adhesive tape to the edge of the backing
paper makes the backing paper tear off easier.
2. Install the side air dam.
NOTE: If the double-sided tape is difficult to affix in cold tem-
perature, etc., warm the bonding surfaces of the body and
side air dam to about 40
−
60
°
C (104
−
140
°
F) before affix-
ing the tape.
3. Firmly press in the side air dam.
AC200049
AC
Protection tape
Double-sided tape
AC200050
AC
Double-sided tape
AC103187
AC103247
Backing paper
Adhesive tape
AE
UNDER COVER
TSB Revision
EXTERIOR
51-16
UNDER COVER
REMOVAL AND INSTALLATION
M1511019600443
AC704710
5
6
7
6
AB
2
1
A
A
4
1
1
2
B
3
Bolt
Front end crossmember
Air dam
skirt panel
Clip (a)
Clip (a)
Section A – A
3.5 ± 1.5 N·m
31 ± 13 in-lb
3.5 ± 1.5 N·m
31 ± 13 in-lb
3.5 ± 1.5 N·m
31 ± 13 in-lb
AC705190AB
1
1
2
: Clip (a)
: Bolt
: Clip (b)
View B (Bolt and clip positions)
REAR SPOILER
TSB Revision
EXTERIOR
51-17
REAR SPOILER
REMOVAL AND INSTALLATION
M1511006100318
Removal steps
1.
Engine room under cover front A
2.
Engine room under cover center
3.
Engine room under cover front B
assembly
4.
Engine room under cover extension
5.
Engine room under cover front B
6.
Engine room side cover
7.
Front floor under cover
Removal steps (Continued)
AC708776
<MR>
AD
3
1
1
4
2
2
2
4
2
A
B
B
C
C
Claw
Claw
Claw
Section B – B
View A
Section C – C
8.5 ± 1.5 N·m
76 ± 13 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
Removal steps
1. Nut
2. Cap
3. Rear spoiler assembly
4. Grommet
Removal steps (Continued)
REAR SPOILER
TSB Revision
EXTERIOR
51-18
INSTALLATION SERVICE POINT
.
>>A<< TAPE INSTALLATION
1. Installation position
CAUTION
• The ambient temperature should be 15 (59) to
40
° C(104° F). Ensure that the working area is clean.
• If ambient temperature is less than 15° C (59° F), heat the
tape and application surface to a temperature of 15 (59)
to 40
° C (104° F).
• Be careful that air bubbles are not formed under the
tape.
2. Installation procedure
(1) Wipe the tape application surface and clean it with a rag
moistened with isopropyl alcohol.
(2) Remove backing paper from the tape, and apply it to the
rear spoiler assembly.
AC705243 AE
2
1
3
3
1
4
4
5.0 ± 1.0 N·m
44 ± 9 in-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
5.0 ± 1.0 N·m
44 ± 9 in-lb
<GSR>
Removal steps
1. Nut
2. Rear spoiler assembly
3. Grommet
>>
A
<< 4. Tape
Removal steps (Continued)
AC609932
Tape
AB
Rear spoiler
assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст