Mitsubishi Evolution X. Manual — part 831
REAR BUMPER ASSEMBLY
TSB Revision
EXTERIOR
51-7
REMOVAL SERVICE POINT
.
<<A>> RIVETS REMOVAL
Refer to FRONT BUMPER DISASSEMBLY SERVICE POINT
(
).
AC708934 AB
10
9
10
11
1
B
A
B
2
3
5
5
10
6
6
15
16
11
9
4
18
N
N
A
Section A – A
Section B – B
Claw
: Claw positions
Screw
Boss
Boss
Screw
20 ± 5 N·m
15 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
13
14
12
7
8
<Vehicles for Canada>
5
N
5.0 ± 2.0 N·m
45 ± 17 in-lb
1.2 ± 0.7 N·m
11 ± 6 in-lb
8.5 ± 1.5 N·m
76 ± 13 in-lb
0.7 ± 0.1 N·m
6 ± 1 in-lb
17
Removal steps
1. Rear bumper assembly
2. Rear bumper extension
3. License plate bracket
4. Rear bumper cover
<<A>> >>A<<
5. Rivet
6. Rear bumper garnish side bracket
7. Rear bumper protector
8. Rear bumper core center
9. Reflector
10. Rear bumper face
11. Rear bumper side bracket
12. Rear bumper core lower
13. Rear bumper core upper
14. Rear bumper core side
15. Rear floor harness
16. Rear bumper reinforcement
17. License plate light assembly
18. Grommet
Removal steps (Continued)
GARNISHES AND MOLDINGS
TSB Revision
EXTERIOR
51-8
INSTALLATION SERVICE POINT
.
>>A<< RIVETS INSTALLATION
Refer to FRONT BUMPER ASSEMBLY SERVICE POINT
(
).
GARNISHES AND MOLDINGS
SPECIAL TOOL
M1511000602292
REMOVAL AND INSTALLATION
M1511004700950
Required Special Tool:
• MB990784: Ornament remover
REMOVAL SERVICE POINTS
.
<<A>> FRONT DELTA GARNISH REMOVAL
Use the ornament remover (MB990784) to remove the front
delta garnish.
.
Tool
Tool number and name Supersession
Application
MB990784
Ornament remover
General service tool
Removal of front delta garnish
MB990784
AC705108
B
2
B
1
2
AB
1
A
A
Roof panel
Clip
Clip
Fender
Section A – A
Section B – B
Front delta garnish removal
<<A>>
1. Front delta garnish
Roof drip molding removal
<<B>>
2. Roof drip molding
DOOR SASH TAPE
TSB Revision
EXTERIOR
51-9
<<B>> ROOF DRIP MOLDING REMOVAL
The following tools are recommended for removing the roof
drip moldings.
Ornament remover set (parts number JS000004)
1. Remover A (parts number JS000001)
2. Remover B (parts number JS000003)
3. Remover C (parts number JS000002)
INQUIRY:
Service Tool Group Manager
No.2 Sales Promotion Dept.
Marketing Operation Office
MITSUBISHI AUTOMOTIVE ACCESSORIES & PRODUCTS
CO.,LTD.
FAX: +81-3-5445-0846
e-mail: sst.map@mitsubishi-motors.com
DOOR SASH TAPE
SPECIAL TOOL
M1511000602300
AC303685
3
2
1
AB
Tool
Tool number and
name
Supersession
Application
MB990528
Stripe tape spatula
General service tool
Installation of door sash tape
MB990528
DOOR SASH TAPE
TSB Revision
EXTERIOR
51-10
REMOVAL AND INSTALLATION
M1511024100477
Required Special Tool:
• MB990528: Stripe tape spatula
REMOVAL SERVICE POINT
.
<<A>> DOOR SASH TAPES REMOVAL
CAUTION
Pay attention to keep from getting burned by hot door
panel or tapes.
1. Use a hair drier to warm the tape.
2. Peel the tip of the tape with your finger, and then peel off the
tape in parallel with the application surface.
Pre-removal and post-installation operation
• Door Window Glass Runchannel Removal and Installation
(Refer to GROUP 42A
− Window Glass Runchannel and
• Door Beltline Molding Removal and Installation (Refer to
GROUP 42A
− Window Glass Runchannel and Door
Opening Weatherstrip
AC706342
1
2
N
N
AB
Removal steps
<<
A
>>
>>
A
<<
1.
Front door sash tape, rear
<<
A
>>
>>A<<
2.
Rear door sash tape, front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст