Mitsubishi Evolution X. Manual — part 832
DOOR SASH TAPE
TSB Revision
EXTERIOR
51-11
INSTALLATION SERVICE POINT
.
>>A<< DOOR SASH TAPES INSTALLATION
CAUTION
• The ambient temperature should be 20(68° F) to
30
° C(86° F). Ensure that the working area is clean. Ide-
ally, the tape application should be done at ambient
temperature of 25
° C(77° F).
• If ambient temperature is less than 15° C(59° F), heat the
tape and application surface to a temperature of 20(68)
to 30
° C(86° F). If ambient temperature is 35° C(95° F) or
higher, cool down them. The adhesive property of the
tape is deteriorated at low temperature, so the tape may
come loose easily. Meanwhile, it gets softened at hot
temperature.
• When beginning to apply the tape, pay particular atten-
tion. If the end of the tape cannot be applied to the
specified position with an accuracy of less than 1
mm(0.04 in), it may cause the poor appearance or adhe-
sion.
• Use the special tool MB990528 to apply the tape with a
steady pace and pressure. If you do not apply the tape
with a steady pace or pressure, or abort the application,
a shallow groove (lateral groove called as "Shock line")
may be present on the tape surface. Meanwhile, if you
apply it too quickly, air bubbles may be formed under
the tape.
1. Wrap a soft cloth (synthetic fiber) around the tip of the
special tool.
2. Use white gasoline to degrease the tape application surface.
3. Wipe away dirt from the tape.
AC303428
AD
MB990528
Unit: mm(in)
MB990528
40 to 50˚
30 to 45˚
10 to 20
(0.39 to 0.79)
10 to 20
(0.39 to 0.79)
Door sash tape
Backing paper
Door sash tape
Backing paper
<Pushing direction>
<Pulling direction>
3 to 7 cm/sec.
3 to 7 cm/sec.
DOOR SASH TAPE
TSB Revision
EXTERIOR
51-12
4. Apply the door sash tape according to the procedure below.
(1) Position the tape at the upper and lower locating points.
(2) Peel of backing strip from the top of the tape and attach it
temporarily.
(3) Peel off the backing strip to the half length of the tape.
(4) Apply the tape using the special tool while peeling off the
remaining backing strip.
AC506859
AC607960AB
4(0.16)
4(0.16)
4(0.16)
4(0.16)
4(0.16)
1(0.04)
3(0.12)
3(0.12)
3(0.12)
: Tape locating points
: T-stud for door opening weatherstrip attaching locations (5 places in all).
Section A – A
B
B
A
A
A
A
Section B – B
Unit: mm (in)
36(1.42)
AC402197
AI
MB990528
Backing paper
Door sash
tape
DOOR SASH TAPE
TSB Revision
EXTERIOR
51-13
(5) For the rear door sash tape, apply it to plain surface (A).
Then apply it to stepped surface (B).
(6) Press the folded area of the tape by three stages (60
° ,
120
° , and holding), rolling in toward the vehicle inside
direction.
AC506860
AB
A
B
Rear door sash tape front
Stepped part
Plain part
AC303415
AG
MB990528
120˚
60˚
Hemming part
SIDE AIR DAM
TSB Revision
EXTERIOR
51-14
SIDE AIR DAM
REMOVAL AND INSTALLATION
M1511005500562
REMOVAL SERVICE POINT
.
<<A>> SIDE AIR DAM REMOVAL
Gently lift and remove the side air dam. If there is any dou-
ble-sided tape remaining on the side air dam, remove accord-
ing to the following instructions.
1. Remove double-sided tape remaining on the body surface
(when replacing side air dam).
AC704709
1
1
1
A
B
B
A
C
C
2
1
2
2
AC
Double-sided tape affixed location
Clip
Splash shield
Clip
Claw
Bolt
Screw
Grommet
Fender
Section C – C
Section B – B
Section A – A
Side outer
panel
Double-sided tape:
4 mm (0.16 in) width and 1.2 mm (0.05 in) thickness
460 mm
(18.11 in)
200 mm
(7.87 in)
Removal steps
<<A>> >>A<<
1. Side air dam
2. Side air dam bracket
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст