Mitsubishi Evolution X. Manual — part 739
SIDE IMPACT SENSOR
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-403
REMOVAL SERVICE POINTS
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCON-
NECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (
−) battery cable from the battery and
tape the terminal to prevent accidental connection and air bag
deployment.
.
<<B>> SIDE IMPACT SENSOR CONNECTOR
REMOVAL
Slide the outer housing of the impact sensor connector in the
arrow direction shown, and disconnect the connector.
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
Check the side impact sensor for dents, breakage and bending
and measure the resistance between the terminals, even when
installing a new side impact sensor.
.
>>B <<SIDE IMPACT SENSOR INSTALLATION
WARNING
If the side impact sensor is not installed securely and
correctly, the side-air bag may not operate normally.
Securely connect the connector.
.
ACX00583
Insulating tape
Battery cable
Battery
AF
AC709474
Side impact sensor
Outer housing of the
impact sensor
connector
AB
SIDE IMPACT SENSOR
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-404
>>C<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition switch to the "ON" position.
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and go out?
4. If yes, the SRS system is functioning properly. If not, refer to
INSPECTION
M1524004700723
WARNING
If a dent, crack, deformation or rust is
detected, replace with a new sensor.
NOTE: For checking of the side impact sensor other
than described below, refer to the section concerning
SRS diagnosis (Refer to
1. Check the side impact sensor and bracket for
dents, cracks or deformation.
2. Check the connector for damage, and terminals
for deformation.
3. Check that there is no bending or corrosion in the
center pillar.
AC709154
SRS warning light
AB
SIDE-AIRBAG MODULE(S)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-405
SIDE-AIRBAG MODULE(S)
REMOVAL AND INSTALLATION
M1524036500148
WARNING
•
Never attempt to disassemble or repair the side-air bag modules. If faulty, replace it.
•
Do not drop the side-air bag modules or allow contact with water, grease or oil. Replace it
if a dent, crack, deformation or rust is detected.
•
Do not expose the side-air bag modules to temperatures over 93
°
C (200
°
F).
•
After deployment of the air bag, replace the air bag module with a new one.
•
Wear gloves and safety glasses when handling air bags that have already deployed.
•
An undeployed side-air bag module should only be disposed of in accordance with the
procedures (Refer to
).
•
When removing and installing the front passenger seat, be sure to carry out accuracy
check occupant classification sensor after the seat has been installed in the vehicle
(On-vehicle Service
).
Pre-removal Operation
• Turn the ignition switch to the "LOCK" (OFF) position.
AC709125
7
7
8
6
2
5
4
3
AB
1
40 ± 4 N·m
30 ± 2 ft-lb
40 ± 4 N·m
30 ± 2 ft-lb
SIDE-AIRBAG MODULE(S)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-406
REMOVAL SERVICE POINT
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCON-
NECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (
−) battery cable from the battery and
tape the terminal to prevent accidental connection and air
bag(s) deployment.
.
<<B>> FRONT SEATBACK REMOVAL
CAUTION
• When replacing the side-air bag module, replace the
front seatback.
• Never use an electric tester to diagnose the air bag
module circuit. Never attempt to disassemble the air
bag module.
• Store the removed front seatback in a clean and dry
place.
• When discarding the air bag module, discard after
deploying the air bag as specified in the service proce-
dure (Refer to
).
Removal steps
<<
A
>>
1.
Negative (
−) battery cable
•
Front seat assembly (Refer to
GROUP 52A, Front Seat Assembly
2.
Seat cushion cover fixation clip
3.
Hinge cover
4.
Reclining adjuster knob
5.
Side shield cover
6.
Front seatback assembly
7.
Headrestraint garnish
<<
B
>>
8.
Front seatback
Installation steps
>>
A
•
Pre-installation inspection
8.
Front seatback
7.
Headrestraint garnish
6.
Front seatback assembly
5.
Side shield cover
4.
Reclining adjuster knob
3.
Hinge cover
2.
Seat cushion cover fixation clip
•
Front seat assembly (Refer to
GROUP 52A, Front Seat Assembly
1.
Negative (
−) battery cable
>>
B
•
Post-installation inspection
ACX00583
Insulating tape
Battery cable
Battery
AF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст