Mitsubishi Outlander XL. Manual — part 742
ZC6000770000
Door hinge
Bolt
Bolt
ZC600078
<Non adjustable bolt>
<Adjusting bolt
(MU001031)>
0000
2.
When the door is not flush with the vehicle body surface.
(1)
Loosen the door-side hinge mounting bolts.
(2)
Move the door to adjust so that the door is flush with the
vehicle body.
(3)
If adjustment is not possible, replace the door-side door
hinge mounting bolt with the adjustment bolt (MU001031).
NOTE:
If the adjustment bolt has been already
installed, reuse it.
(4)
Move the door to adjust so that the door is flush with the
vehicle body.
(5)
Tighten the door-side door hinge mounting bolt to the
specified torque.
Tightening torque: 26 ± 6 N?m (19 ± 5 ft-lb)
ZC6000660000
MB990939
Striker
Temporary
bolts
ZC6000670000
MB990211
MB990243
Striker
ZC6000680000
Shim
Striker
3.
When the door is stiff to close and open
(1)
Adjustment using the striker (toward the inside of the
vehicle and vertical direction)
Install a temporary bolt instead of the striker mounting bolt,
and use special tool MB990939 and a hammer to tap the
bolt in the desired direction.
(2)
Adjustment by using the striker (toward the outside of the
vehicle)
Use special tools MB990211 and MB990243 to pull the
striker toward the outside of the vehicle.
(3)
Adjustment using shims (forward and rearward)
Increase or decrease the number of shims so that the
striker engages with the door latch properly.
DOOR
42Ab-87
ON-VEHICLE SERVICE
DOOR WINDOW GLASS ADJUSTMENT
M14203000013USA0000010000
Check that the door glass operates smoothly and moves along
the door glass run channel when the door window glass is fully
raised and fully lowered. If there is a problem, adjust by the
following procedure.
1.
Remove the door trim assembly (Refer to GROUP 52A, Door
Trim P.52A-11).
2.
Remove the waterproof film (Refer to P.42Ab-110).
AC5070890000
<Front door>
Channel guide mounting bolts
3.
Raise the door window glass and loosen the channel guide
mounting bolts to adjust tilting up/down of the glass.
POWER WINDOW CHECK
M14203000901USA0000010000
Check the power window as described below. If it does not work,
perform troubleshooting (Refer to P.42Ab-39).
⦆
Turn off the power window lock switch of the power window
main switch, and operate each of the power window switches
to check that each power window operates.
⦆
Turn on the power window lock switch of the power window
main switch, and operate the front and rear passenger's power
window sub switches to check that the power windows do not
work.
⦆
Turn on the power window lock switch of the power window
main switch, and operate the power window main switch to
check that each power window operates.
NOTE:
The power window lock switch function can be
adjusted with the customization feature, confirm it
before check (Refer to P.42Ab-94).
ADJUSTMENT OF FAULTY POWER WINDOW
M14203000902USA0000010000
If the door window glass wrongly, automatically lowers while
being raised, adjust or replace as follows:
1.
Remove the door trim assembly (Refer to GROUP 52A, Door
Trim P.52A-11).
2.
Remove waterproof film (Refer to P.42Ab-110).
3.
Remove the window regulator assembly from the door window
glass, and then raise and lower the door window glass by hand
to check the operation force.
42Ab-88
DOOR
ON-VEHICLE SERVICE
ZC6000700000
Runchannel
Door
sash
Lower
sash
4.
If the door window glass does not move up and down
smoothly, check and repair as follows:
⦆
Check the installation condition of the runchannel.
⦆
Straighten twist in the door sash.
⦆
Check the installation condition of the lower sash.
5.
If repair or adjustment is impossible, replace the door
assembly.
POWER WINDOW SAFETY MECHANISM CHECK
<Driver’s side only>
M14203000984USA0000010000
ZC6000710000
1.
Place an approximately 10 mm (0.39 inch) thick wood chip as
shown. Then, raise the window glass.
2.
Check that the window lowers by about 150 mm (5.9 inches)
when the window clamps the board. If this doesn't happen, do
troubleshooting. Refer to P.42Ab-39.
NOTE:
If the anti-trap function (safety mechanism) is
activated consecutively three times or more, carry out
the learning procedures of the power window fully closed
position (Refer to P.42Ab-88).
POWER WINDOW TIMER FUNCTION CHECK
M14203000904USA0000010000
Check the power window timer as described below. If it does not
work, perform troubleshooting (Refer to P.42Ab-39).
⦆
Close the door and turn the ignition switch to the LOCK (OFF)
position, and then check that the power windows operate for
30 seconds.
⦆
Close the door and turn the ignition switch to the LOCK (OFF)
position. While the timer is on, open the driver's door or front
passenger's door, and check that the timer is cancelled.
POWER WINDOW OPERATION CURRENT CHECK
M14203000905USA0000010000
ZC6011500002
Power window fuse
ETACS-ECU
1.
Remove the power window fuse, and connect a multimeter as
shown in the illustration.
2.
Raise the power window to measure the current during
operation.
Standard value: 7 A or less [Power supply voltage
14.5 ± 0.5 V, at 25°C (77°F)]
NOTE:
If the power supply voltage does not meet the
standard value, check and repair the generator and the
battery. Then carry out this check again.
3.
If the operation current is outside the standard value, refer
to P.42Ab-88.
DOOR
42Ab-89
ON-VEHICLE SERVICE
LEARNING PROCEDURES OF THE POWER
WINDOW FULLY CLOSED POSITION
M14203000924USA0000010000
LEARNING PROCEDURES OF THE FULLY
CLOSED POSITION WHEN THE POWER WINDOW
SWITCH IS REMOVED, OR THE POWER WINDOW
REGULATOR ASSEMBLY IS REMOVED OR
REPLACED
1.
If the anti-trap function (safety mechanism) is activated
consecutively three times or more, the fully closed position
that the power window switch has learned will be erased
(initialised).
2.
Operate the power window switch and fully open the door
window glass.
The anti-trap function will not activated until the learning
procedures of the fully closed position have been
completed (because the anti-trap function was reset).
3.
Operate the power window switch and fully close the door
window glass. The power window activates for 0.7 seconds
and stops automatically when the power window switch is
pressed once. Repeat this operation until the door window
glass fully closes and release the switch once. Then, hold the
power window switch to the fully closed side again for one
second so that the power window switch completes learning
the fully closed position.
NOTE:
If the power window switch is operated to open the
door window glass while the switch is learning, the
learning will be cancelled. If this happens, return to
step 2.
LEARNING PROCEDURES WHEN THE POWER
WINDOW SWITCH IS REPLACED WITH A NEW
ONE
The anti-trap function will not activated until the learning
procedures of the fully closed position have been
completed (because the anti-trap function was reset).
Operate the power window switch to fully close the door window
glass by one-shot up action so that the power window switch will
complete learning (no initialization is required).
42Ab-90
DOOR
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст