Mitsubishi Outlander XL. Manual — part 731
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Are power window main switch connector E-19, front
power window motor (LH) connector E-16 in good
condition?
YES:
Go to Step 2.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Verify
that the power window works normally.
STEP 2. Check the wiring harness between power window
main switch connector E-19 (terminals 9, 11 and 12) and
front power window motor (LH) connector E-16 (terminals
5, 2 and 6).
Q:Is the wiring harness between power window main switch
connector E-19 (terminals 9, 11 and 12) and front power
window motor (LH) connector E-16 (terminals 5, 2 and 6)
in good condition?
YES:
Go to Step 3.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. Verify that the power window works
normally.
STEP 3. Diagnostic trouble code recheck
Replace the front power window motor (LH). Recheck if the
diagnostic trouble code is set.
(1)
Erase the diagnostic trouble code.
(2)
Operate the driver’s door window switch on the power
window main switch.
(3)
Check if the diagnostic trouble code is set.
Q:Is the diagnostic trouble code set?
YES:
Replace the power window main switch.
NO:
The procedure is complete. Verify that the power
window works normally.
CODE NO. L0734 P/W (DR) Above window position
M14203000934USA0000010000
COMMENTS ON TROUBLE SYMPTOM
If the driver's door window glass exceeds the fully closed
position, power window main switch sets the diagnostic trouble
code No. L0734.
PROBABLE CAUSES
⦆
Malfunction of the front power window motor (LH)
⦆
Malfunction of the power window main switch
DOOR
42Ab-43
POWER WINDOW DIAGNOSIS
DIAGNOSTIC PROCEDURE
STEP 1. Check the power window fully closed position
(1)
Carry out the learning procedures of the power window fully
closed position. Refer to P.42Ab-90.
(2)
Recheck if the diagnostic trouble code is set.
Erase the diagnostic trouble code.
Press the driver’s door window switch (on the power window
main switch) down to open the window, and pull up the
driver’s door window switch to fully does the window.
Check if the diagnostic trouble code is set.
Q:Is the check result normal?
YES:
The procedure is complete.
NO:
Go to Step 2.
STEP 2. Diagnostic trouble code recheck
Replace the front power window motor (LH). Recheck if the
diagnostic trouble code is set.
(1)
Erase the diagnostic trouble code.
(2)
Press the driver’s door window switch (on the power window
main switch) down to open the window, and pull up the
driver’s door window switch to fully does the window.
(3)
Check if the diagnostic trouble code is set.
Q:Is the diagnostic trouble code set?
YES:
Replace the power window main switch.
NO:
The procedure is complete. Verify that the power
window works normally.
CODE NO. L0736 P/W (DR) Sensor fail (ground)
M14203000935USA0000010000
Before replacing the ECU, ensure that the input
and output signal circuits are normal.
42Ab-44
DOOR
POWER WINDOW DIAGNOSIS
ZC601368
GREEN-WHITE
GREEN
ORANGE
ORANGE
VIOLET
BLA
CK
BLA
CK
POWER WINDOW MAIN SWITCH
FRONT
POWER
WINDOW
MOTOR (LH)
FRONT
(LH)
CPU
LIN DRIVE
CIRCUIT
IC
IC
BLA
CK-YELLO
W
0000
Driver’s Power Window Circuit
ZC600881
Connectors: E-16, E-19
E-19
E-16 (GR)
0003
COMMENTS ON TROUBLE SYMPTOM
If the earth fault of the front power window motor (LH)
sensor power supply is detected, power window main
switch sets the diagnosis trouble code No. L0736
PROBABLE CAUSES
⦆
Malfunction of the front power window motor (LH)
⦆
Malfunction of the power window main switch
⦆
Damaged wiring harness and connectors
DIAGNOSTIC PROCEDURE
STEP 1. Check power window main switch connector E-19,
front power window motor (LH) connector E-16 for loose,
DOOR
42Ab-45
POWER WINDOW DIAGNOSIS
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Are power window main switch connector E-19, front
power window motor (LH) connector E-16 in good
condition?
YES:
Go to Step 2.
NO:
Repair or replace the damaged component(s). Refer to
GROUP 00E, Harness Connector Inspection P.00E-2. Verify
that the power window works normally.
STEP 2. Check the wiring harness between power window
main switch connector E-19 (terminal 12) and front power
window motor (LH) connector E-16 (terminal 6).
Q:Is the wiring harness between power window main switch
connector E-19 (terminal 12) and front power window
motor (LH) connector E-16 (terminal 6) in good
condition?
YES:
Go to Step 3.
NO:
The wiring harness may be damaged or the connector
(s) may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the wiring
harness as necessary. Verify that the power window works
normally.
STEP 3. Diagnostic trouble code recheck
Replace the front power window motor (LH). Recheck if the
diagnostic trouble code is set.
(1)
Erase the diagnostic trouble code.
(2)
Operate the driver’s door window switch on the power
window main switch.
(3)
Check if the diagnostic trouble code is set.
Q:Is the diagnostic trouble code set?
YES:
Replace the power window main switch.
NO:
The procedure is complete. Verify that the power
window works normally.
CODE NO. L0740 P/W (DR) 3 times jam - protection
M14203000936USA0000010000
COMMENTS ON TROUBLE SYMPTOM
If the anti-trap function is activated consecutively three times or
more, power window main switch sets the diagnostic trouble
code No. L0740.
PROBABLE CAUSES
⦆
Malfunction of the front power window motor (LH)
⦆
Malfunction of the power window main switch
DIAGNOSTIC PROCEDURE
42Ab-46
DOOR
POWER WINDOW DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст