Mitsubishi Outlander XL. Manual — part 831
Item No.
Check items
Check
conditions
Normal conditions
36
Threshold of PRS. warning
The
tire
pressure
is
within
the
specified value
range.
OFF
The
tire
pressure is not
within
the
specified value
range.
ON
37
Threshold of PRS. warning
release
The
tire
pressure
is
within
the
specified value
range.
ON
The
tire
pressure is not
within
the
specified value
range.
OFF
38
Number of registered TPMS ID
-
Number of stored TPMS
41
VSS
Drive
the
vehicle
The scan tool and the tachometer
readings are approximately the same
CHECK AT ECU TERMINALS
M14209200046USA0000010000
ZC603896
C-29
0001
Terminal
No.
Check items
Check conditions
Normal conditions
1 - 5
-
-
-
6
Power supply (Battery)
Always
Battery voltage
7
Ground
Always
0 V
8
-
-
-
9
Power supply (Ignition switch: IG1) Ignition switch: ON
Battery voltage
10
CAN L
-
-
11
CAN H
-
-
WIRELESS CONTROL MODULE (WCM)
42C-83
DIAGNOSIS
SPECIAL TOOLS
M14209200003USA0000010000
Tool
Tool number and
name
Supersession
Application
MB991910
MB991826
YB9919580000
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
Do not use
a
b
c
d
e
f
g
MB991958
a.
MB991824
b.
MB991827
c.
MB991910
d.
MB991911
e.
MB991914
f.
MB991825
g.
MB991826
M.U.T.-III
sub
assembly
a.
Vehicle
communication
interface (V.C.I.)
b.
M.U.T.-III
USB
cable
c.
M.U.T.-III
main
harness
A
(Vehicles
with
CAN
communication
system)
d.
M.U.T.-III
main
harness
B
(Vehicles without
CAN
communication
system)
e.
M.U.T.-III
main
harness C (for
Daimler Chrysler
models only)
f.
M.U.T.-III
measurement
adapter
g.
M.U.T.-III trigger
harness
MB991824-KIT
NOTE:
G: MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I. ENTER
key.
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
⦆
Check of the diagnostic trouble
code and service data
⦆
Registration of ID codes
42C-84
WIRELESS CONTROL MODULE (WCM)
SPECIAL TOOLS
Tool
Tool number and
name
Supersession
Application
YB9912230000
Do not use
a
b
c
d
MB991223
a.
MB991219
b.
MB991220
c.
MB991221
d.
MB991222
Harness set
a.
Test harness
b.
LED harness
c.
LED
harness
adaptor
d.
Probe
General service tools Continuity check and voltage
measurement at harness wire or
connector for loose, corroded or
damaged terminals, or terminals
pushed back in the connector.
a.
Connector
pin
contact
pressure inspection
b.
Power circuit inspection
c.
Power circuit inspection
d.
Commercial tester connection
MB992006
MB992006
Extra fine probe
-
Making voltage and resistance
measurement
during
troubleshooting
ON-VEHICLE SERVICE
ID CODES REGISTRATION PROCEDURE
M14209200048USA0000010000
The ID codes necessary for the engine immobilizer
system, the keyless entry system and the TPMS can
be registered using the M.U.T.-III.
If the ignition key with transmitter is added or
replaced, register the key (key ID), and then
register the keyless entry secret code again.
WIRELESS CONTROL MODULE (WCM)
42C-85
ON-VEHICLE SERVICE
SUPPLY UNIT LIST FOR INDIVIDUAL KEY
Ignition key (with transmitter)
NOTE:
Blank key (It is the key that
comes with the door service key set and
the glove box service key set. It can
only be used for locking and unlocking,
and it cannot start the engine.)
ZC6037530000
ZC6044010001
Blank key
KEY SUPPLY UNIT LIST FOR OTHER THAN INDIVIDUAL KEY
Full service key set
Handle lock service key
set
Door service key set
Glove box service key
set
ZC6045380000
ZC6045400000
ZC6045500000
ZC6045390000
NOTE:
⦆
When re-registering the key (key ID), all the keys
(key ID) registered before must be re-registered
because all of them will be erased.
⦆
After registering the keys, make sure that the
engine is started normally with all of the keys
registered.
42C-86
WIRELESS CONTROL MODULE (WCM)
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст