Mitsubishi Outlander XL. Manual — part 927

DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the passenger's seat
belt pre-tensioner (squib).

TROUBLESHOOTING HITS

｠

Damaged wiring harnesses or connectors

｠

Short to the power supply in the passenger's seat
belt pre-tensioner (squib) harness

｠

Malfunction of the SRS-ECU

DIAGNOSIS

Required Special Tools:

｠

MB991958: Scan Tool (M.U.T.-III Sub Assembly)

｠

MB991824: Vehicle Communication Interface (V.C.I.)

｠

MB991827: M.U.T.-III USB Cable

｠

MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN Communication System)

｠

MB991865: Dummy resistor

｠

MB991884: Resister harness

STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.

(1)

Connect scan tool MB991958. Refer to "How to connect the
scan tool P.52B-31."

(2)

Turn the ignition switch to the "ON" position.

(3)

Diagnose the CAN bus line.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the CAN bus line found to be normal?

YES:

Go to Step 2.

NO:

Repair the CAN bus line (Refer to GROUP 54D,

Diagnosis P.54D-17).

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-239

SRS AIR BAG DIAGNOSIS

STEP 2. Recheck for diagnostic trouble code.

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

Check again if the DTC is set.

(1)

Erase the DTC.

(2)

Turn the ignition switch to "ON" position.

(3)

Check if the DTC is set.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is the DTC set?

YES:

Go to Step 3.

NO:

There is an intermittent malfunction such as poor

engaged connector(s) or open circuit (Refer to GROUP 00,
How to Cope with Intermittent Malfunction P.00-15).

STEP 3. Check the passenger's seat belt pre-tensioner.
(Using scan tool MB991958, read the diagnostic trouble
code.)

(1)

Disconnect the negative battery terminal.

ZC6018230001

Seat belt
pre-tensioner

Floor wiring harness side
connector (2-pin, black)

Locking
button

Flat-tipped
screwdriver

(2)

Disconnect passenger's seat belt pre-tensioner connector
D-130. Use a flat-tipped screwdriver to unlock the locking
button at the harness side connector by withdrawing it toward
you in two stages, and then disconnect the connector.

ZC600214

Harness side
connector

MB991865
(Dummy resistor: 3

)

MB991884
(Resistor harness)

0000

(3)

Connect special tool MB991865 to special tool MB991884.

(4)

Connect special tool MB991884 to the D-130 harness side
connector.

(5)

Connect the negative battery terminal.

(6)

Erase diagnostic trouble code memory, and then check the
diagnostic trouble code.

Q:Is DTC B1C48 set?

YES:

Go to Step 4.

NO:

Replace the passenger's seat belt with pre-tensioner

(Refer to P.52B-345). Then go to Step 6.

STEP 4. Check the passenger's seat belt pre-tensioner
circuit. Measure the voltage at the SRS-ECU connector
C-27.

(1)

Disconnect SRS-ECU connector C-27.

52B-240

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

SRS AIR BAG DIAGNOSIS

ZC6018230001

Seat belt
pre-tensioner

Floor wiring harness side
connector (2-pin, black)

Locking
button

Flat-tipped
screwdriver

(2)

Disconnect passenger's seat belt pre-tensioner connector
D-130. Use a flat-tipped screwdriver to unlock the locking
button at the harness side connector by withdrawing it toward
you in two stages, and then disconnect the connector.

(3)

Turn the ignition switch to the "ON" position,

ZC5007950021

C-27 Harness side
connector (front view)

Do not insert a test probe into the terminal from its front side
directly, as the connector contact pressure may be
weakened.

(4)

Measure the voltage between C-27 harness side connector
terminals 43, 44 and body ground.
Voltage should measure 0 volt.

Q:Is the measured voltage 0 volt?

YES:

Erase the diagnostic trouble code memory, and check

the diagnostic trouble code. If DTC B1C48 sets, replace
the SRS-ECU (Refer to P.52B-326). Then go to Step 6.

NO:

Go to Step 5.

STEP 5. Check the harness wires for short circuit to power
supply between SRS-ECU connector C-27 (terminal No.43
and 44) and passenger's seat belt pre-tensioner connector
D-130 (terminal No.2 and 1).

Q:Are the harness wires between SRS-ECU connector C-27

(terminal No.43 and 44) and passenger's seat belt pre-

tensioner connector D-130 (terminal No.2 and 1) in good

condition?

YES:

Go to Step 6.

NO:

Replace the harness wires between SRS-ECU connector

C-27 and passenger's seat belt pre-tensioner connector
D-130. Then go to Step 6.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

52B-241

SRS AIR BAG DIAGNOSIS

STEP 6. Recheck for diagnostic trouble code.

ZC501967

AC404789

ZC5019680000

MB991824

MB991827

MB991910

Data link

connector

Check again if the DTC is set.

(1)

Erase the DTC.

(2)

Turn the ignition switch to the "ON" position.

(3)

Check if the DTC is set.

(4)

Turn the ignition switch to the "LOCK" (OFF) position.

Q:Is DTC B1C48 set?

YES:

Return to Step 1.

NO:

The procedure is complete.

52B-242

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

SRS AIR BAG DIAGNOSIS