Mitsubishi Outlander XL. Manual — part 950
Driver's air bag module installation
steps
>>D<<
·
Driver's air bag module connector
connection
>>D<<
·
Horn connector connection
2.
Cover
1.
Negative (-) battery cable connection
>>E<<
·
Post-installation inspection
Clock spring removal steps
<<A>>
1.
Negative (-) battery cable connection
<<B>>
2.
Cover
·
Horn connector connection
<<C>>
·
Driver's air bag module connector
connection
<<D>>
3.
Driver's air bag module
<<E>>
4.
Steering wheel assembly
·
Lower, upper column cover
5.
Paddle shift assembly <vehicles with
paddle shift>
Clock spring removal steps
<<F>>
6.
Clock spring
Clock spring installation steps
>>A<<
Pre-installation inspection
>>B<<
6.
Clock spring
·
Lower, upper column cover
5.
Paddle shift assembly <vehicles with
paddle shift>
>>C<<
4.
Steering wheel assembly
>>C<<
3.
Driver's air bag module
>>D<<
·
Driver's air bag module connector
connection
>>D<<
·
Horn connector connection
2.
Cover
1.
Negative (-) battery cable connection
>>E<<
·
Post-installation inspection
·
Steering wheel sensor calibration
(Refer to GROUP 35C, On-vehicle
Service - Steering Wheel Sensor
Calibration P.35C-192.)
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824:Vehicle Communication Interface
(V.C.I.)
⦆
MB991827:M.U.T.-III USB Cable
⦆
MB991910:M.U.T.-III Main Harness A
⦆
MB992006: Extra Fine Probe
⦆
MB990803: Steering Wheel Puller
PASSENGER'S (FRONT) AIR BAG MODULE
ZC601328
5.0 ± 1.0 N·m
44 ± 9 in-lb
1
2
AA00
Passenger's (front) air bag module
removal steps
<<A>>
1.
Negative (-) battery cable connection
<<G>>
·
Passenger's (front) air bag module
connector
Passenger's (front) air bag module
removal steps
·
Instrument panel assembly (Refer to
GROUP 52A, Instrument Panel
Assembly P.52A-2.)
<<H>>
2.
Passenger's (front) air bag module
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-331
AIR BAG MODULE(S) AND CLOCK SPRING
Passenger's (front) Installation
steps
>>A<<
·
Pre-installation inspection
2.
Passenger's (front) air bag module
·
Instrument panel assembly (Refer to
GROUP 52A, Instrument Panel
Assembly P.52A-2.)
Passenger's (front) Installation
steps
·
Passenger's (front) air bag module
connector
·
Negative (-) battery connection
>>E<<
·
Post-installation inspection
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface
(V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
⦆
MB992006: Extra Fine Probe
REMOVAL SERVICE POINTS
<<A>> NEGATIVE (-) BATTERY CABLE DISCONNECTION
Wait at least 60 seconds after disconnecting the battery
cable before doing any further work. (Refer to P.52B-28).
Battery posts, terminals and related accessories contain
lead and lead compounds. WASH HANDS AFTER
HANDLING.
ZC500608
Battery
Insulating tape
0000
Battery cable
Disconnect the negative (-) battery cable from the battery and
tape the terminal to prevent accidental connection and air bag
(s) deployment.
<<B>> COVER REMOVAL
ZC601548
MB990784
Cover
0000
Insert the ornament remover (Special tool: MB990784) into the
notch shown in the figure, and remove the cover.
52B-332
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
AIR BAG MODULE(S) AND CLOCK SPRING
<<C>> DRIVER’S AIR BAG MODULE CONNECTOR
REMOVAL
ZC601709
AC600868
Outer housing of the driver’s air bag
module connector
Horn connector
Lower column cover
0000
Driver’s air bag
module connector
(4-pin, yellow)
Slide the outer housing of the driver’s air bag module connector
in the arrow direction shown, and disconnect the connector.
<<D>> AIR BAG MODULE ASSEMBLY REMOVAL
⦆
The air bag module must not be measured with such
equipment as an ohmmeter.
⦆
The air bag module must not be disassembled.
⦆
The removed air bag module should be stored in a clean,
dry place with the deployment surface facing up.
Loosen the torx screw and remove the air bag module assembly.
<<E>> STEERING WHEEL ASSEMBLY REMOVAL
ZC600290
MB990803
0000
Use special tool MB990803 to remove the steering wheel.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-333
AIR BAG MODULE(S) AND CLOCK SPRING
<<F>> CLOCK SPRING REMOVAL
The removed clock spring should be stored in a clean, dry
place.
<<G>> PASSENGER'S (FRONT) AIR BAG MODULE
CONNECTOR REMOVAL
ZC601552
Passenger's (front) air bag module
connector (4-pin, yellow)
Outer housing
of the passenger’s
air bag module
connector
Heater unit
0000
Slide the outer housing of the passenger’s (front) air bag module
connector in the arrow direction shown, and disconnect the
connector.
<<H>> PASSENGER'S (FRONT) AIR BAG MODULE
REMOVAL
⦆
The air bag module must not be measured with such
equipment as an ohmmeter.
⦆
The air bag module must not be disassembled.
⦆
The removed air bag module should be stored in a clean,
dry place with the deployment surface facing up.
ZC601553
Flat-tipped
screwdriver
Flat-tipped screwdriver
Passenger's (front)
air bag module
0000
Insert a slotted (-) screwdriver or similar tool to the location
shown in the figure. After disengaging the tabs, remove the front
passenger's air bag module.
INSTALLATION SERVICE POINTS
>>A<< PRE-INSTALLATION INSPECTION
Dispose of air bag modules only according to the specified
procedure (Refer to P.52B-352).
1.
When installing the new air bag modules and clock spring,
refer to “INSPECTION” ( P.52B-336).
52B-334
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
AIR BAG MODULE(S) AND CLOCK SPRING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст