Mitsubishi Outlander XL. Manual — part 856
Move the nozzle to adjust the position so that the spray is in the
area shown in the illustration.
WINDSHIELD WASHER SWITCH CHECK
Check the windshield washer switch from the ETACS diagnosis
codes for proper operation.(Refer to GROUP 54Ad,
DIAGNOSTIC TOUBLE CODE CHART P.54Ad-8.)
REAR WIPER AND WASHER
REMOVAL AND INSTALLATION
M15102100028USA0000010000
ZC600460
2
1
7
1
8
4
6
3
0000
5
A
A
Section A–A
Tailgate spoiler
4.5 ± 1.5 N·m
39 ± 13 in-lb
7.5 ± 1.5 N·m
67 ± 13 in-lb
·
Washer tank (Refer to P.51B-55)
·
Washer motor (Refer to P.51B-55)
Rear washer nozzle removal steps
·
Liftgate spoiler (Refer to P.51A-20)
WIPER AND WASHER
51B-57
REAR WIPER AND WASHER
Rear washer nozzle removal steps
·
High-mounted stop light assembly
(Refer to P.51A-20)
1.
Rear washer nozzle assembly
Rear wiper blade removal steps
2.
Rear wiper blade assembly
>>A<<
3.
Rear wiper blade
Rear wiper motor removal steps
4.
Cover
>>B<<
5.
Rear wiper arm assembly
·
Liftgate trim (Refer to GROUP 52A,
Liftgate Trim P.52A-14)
Rear wiper motor removal steps
6.
Grommet
7.
Rear wiper motor assembly
Rear washer hose removal steps
·
Front/rear scuff plate, cowl side trim,
quarter trim (Refer to GROUP 52A,
Interior Trim P.52A-10)
·
Liftgate trim (Refer to GROUP 52A,
Liftgate Trim P.52A-14)
8.
Rear washer hose
NOTE:
For removal and installation of the wiper
and washer switch, refer to GROUP 54Ah, Column
Switch P.54Ah-8.
INSTALLATION SERVICE POINTS
>>A<< REAR WIPER BLADE INSTALLATION
ZC6001590000
A
A
Wiper blade
Backing
Backing
Section A – A
Wiper
blade
Backing
Use a curved backing like that shown for the backing of a
wiper blade to ensure sustained wiper wiping performance.
>>B<< REAR WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
ZC6004610000
A
Rear wiper arm and
blade assembly
Ceramic line terminal
Assemble the wiper blade so that their edge stops at the
specified position.
(A): 0 to 20 mm(0 to 0.79 in) from edge of the ceramic
line
51B-58
WIPER AND WASHER
REAR WIPER AND WASHER
INSPECTION
M15102100029USA0000010000
REAR WIPER MOTOR CHECK
AC103246
ZC6004620000
Operation check
Stop position check
Inspect the rear wiper motor by disconnecting the harness
connector with the motor attached to the vehicle.
REAR WIPER MOTOR OPERATION CHECK
Connect the battery to the rear wiper motor to inspect the motor
operation as shown in the illustration.
REAR WIPER MOTOR STOP POSITION CHECK
1.
Connect the battery to the rear wiper motor as shown in the
illustration.
2.
Disconnect the battery in the middle of the motor rotation and
check to see that the motor stops.
3.
Reconnect the battery.
4.
Check to see that the rear wiper motor runs and then stops
at the automatic stop position.
WIPER AND WASHER
51B-59
REAR WIPER AND WASHER
REAR WASHER MOTOR INSPECTION
ZC6004630000
Rear washer
hose
1.
The rear washer motor must be checked with the washer tank
installed and the washer fluid filled.
2.
Connect the battery to the washer motor connector as shown.
Check that the washer motor delivers washer strongly to the
rear washer hose side.
CHECKING THE REAR WASHER NOZZLE
INJECTION DIRECTION
ZC600464
3(0.12)
0000
Unit: mm(in)
40(1.57)
25(0.98)
180(7.09)
25(0.98)
Rear washer nozzle
Liftgate spoiler
Ceramic
line terminal
Vehicle center line
Adjust the nozzle so that it injects washer fluid to the range
shown.
CHECKING THE REAR WIPER AND WASHER
SWITCH
The rear wiper and washer switch can be checked for proper
operation by confirming ETACS diagnostic trouble code.(Refer
to GROUP 54Ad, DIAGNOSTIC TOUBLE CODE CHART P.
54Ad-8.)
51B-60
WIPER AND WASHER
REAR WIPER AND WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст