Mitsubishi Outlander XL. Manual — part 835
INSPECTION
M14209200057USA0000010000
TRANSMITTER BATTERY CHECK
AC004486
Measure the voltage of the battery. If the voltage of the battery
is not within the standard value, replace the battery.
Standard value:2.5 - 3.2 V
TPMS TRANSMITTER
REMOVAL AND INSTALLATION
M14209200072USA0000010000
⦆
Ensure valve cap is always in place except when
adjusting tire pressure.
⦆
If the valve core and valve cap are replaced, use
a genuine replacement part. The valve core is
similar to a conventional one, but uses nickel
plating to avoid corrosion.
⦆
Replace the valve stem grommet and washer
with a new one every five years or when the tire
is replaced.
⦆
Do not drop the TPMS transmitter from height
greater than 1 meter (3.3 feet).
⦆
Do not expose the TPMS transmitter to
extraneous magnetic fields.
⦆
TPMS transmitter should not be stored at
temperatures above 80°C (176°F).
⦆
TPMS transmitter should not be exposed to
temperatures above 100°C (212°F).
⦆
If the TPMS transmitter is replaced, execute
"Tire Pressure Sensor ID Registration" on scan
tool MB99158 "Special Function."
Pre-removal Operation
⦆
Wheel and Tire Removal
Post-installation Operation
⦆
Wheel and Tire Installation
⦆
Tire Pressure Sensor ID Registration If a new TPMS transmitter is installed (Refer to P.42C-92.)
⦆
After the tire pressure sensor ID registration, check that the TPMS warning light does not illuminate
or flash.
WIRELESS CONTROL MODULE (WCM)
42C-99
TRANSMITTER
ZC6045420000
1
2
3
4
N
8.0 ± 0.5 N·m
71 ± 4 in-lb
0.25 N·m
2.5 in-lb
5
REMOVAL STEPS
<<A>>
1.
VALVE CAP
<<A>>
2.
VALVE NUT
·
LET TPMS TRANSMITTER
FALL INTO TIRE
·
TIRE BEAD
<<B>>
3.
TPMS TRANSMITTER
<<C>>
4.
GROMMET
<<C>>
5.
WASHER
INSTALLATION STEPS
>>A<<
5.
WASHER
INSTALLATION STEPS
>>A<<
4.
GROMMET
>>A<<
3.
TPMS TRANSMITTER
>>A<<
2.
VALVE NUT
>>B<<
·
TIRE BEAD MOUNTING
>>C<<
·
TIRE PRESSURE INFLATION
>>C<<
·
VALVE NUT RETIGHTENING
1.
VALVE CAP
REMOVAL SERVICE POINTS
<<A>> VALVE CAP/VALVE NUT REMOVAL
Ensure valve cap is always in place except when adjusting
tire pressure.
1.
Remove the valve cap.
2.
Rotate tire so that valve stem is in the 6 o’clock position.
3.
Use a long-reach 17.2 mm (0.68 inch) socket to unscrew the
valve nut and remove it. Slowly push valve stem into tire so
that tire pressure is relieved.
4.
Once tire pressure is relieved, let TPMS transmitter into tire.
42C-100
WIRELESS CONTROL MODULE (WCM)
TPMS TRANSMITTER
<<B>> TPMS TRANSMITTER REMOVAL
ZC6008320000
TPMS
Transmitter
1.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains in the bottom of the tire.
Be careful not to damage the TPMS transmitter.
2.
Lubricate tire well and remove outer side of the tire.
3.
Reach inside the tire and remove the TPMS transmitter.
4.
Remove tire from rim using proper tire changing equipment
procedures.
<<C>> GROMMET/WASHER REMOVAL
⦆
Do not vary the angle of valve except at mounting on the
rim. If varying the angle over and over, it may cause
breakage of antenna plate resulting in the failure of
transmitter.
⦆
Use a soft tool to remove the grommet and washer to
prevent scratching the valve of the TPMS transmitter.
Remove the grommet and washer from the TPMS transmitter.
INSTALLATION SERVICE POINTS
>>A<< GROMMET/WASHER/TPMS TRANSMITTER/VALVE
NUT INSTALLATION
When installing a new grommet and washer, make sure to
support the valve stem base with a thumb so that there is
no movement of the stem. Otherwise, the stem may
protrude resulting in the breakage of antenna plate.
1.
Install a new grommet and washer to the TPMS transmitter.
ZC6045430000
TPMS transmitter
Grommet
Valve nut
Holes
Washer
⦆
Visually check that TPMS transmitter is not deformed or
damaged.
⦆
When installing the TPMS transmitter, be sure the rim,
grommet and valve nut are clean.
⦆
Ensure the grommet is located inside the valve hole
before installing the valve nut.
⦆
While installing the valve nut, push the transmitter to
maintain the lower lip of the transmitter case is in contact
with the rim without clearance.
⦆
While installing the valve nut, ensure the tool is kept
aligned to the valve and the valve hole.
⦆
After installing the valve nut, check that the grommet is
compressed and washer is bend.
WIRELESS CONTROL MODULE (WCM)
42C-101
TPMS TRANSMITTER
2.
Mount TPMS transmitter valve through rim hole as illustrated.
Pressure holes in the transmitter case should face away from
center of rim. Tighten valve nut finger tight, then slowly torque
the valve nut to 8.0 ± 0.5 N·m (71 ± 4 in-lb).
Install the TPMS transmitter correctly. If the TPMS
transmitter is installed incorrectly, it may not work
correctly, or become damaged when the tire is installed.
3.
Check that the TPMS transmitter is correctly assembled
(Refer to illustration).
⦆
Lower lip of the TPMS transmitter case is touching the rim
after torquing.
>>B<< TIRE BEAD MOUNTING
ZC604545 AA00
1.
Put the tire on the rim, so that the cross point of the belt with
the rim is approximately 20 cm (7.9 inch) away from the valve
ZC604546AA00
2.
Engage the shoe and make sure that 20 cm (7.9 inch) is
maintained between the cross point and the valve. The arrow
shows the direction of rotation of the wheel.
ZC604547AA00
3.
Turn the wheel in order to engage all the first side of the tire.
NOTE:
The standard shoes can pass over the sensor without
damaging it.
42C-102
WIRELESS CONTROL MODULE (WCM)
TPMS TRANSMITTER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст