Mitsubishi Outlander XL. Manual — part 833
KEYLESS ENTRY SYSTEM CHECK
M14209200049USA0000010000
Check the keyless entry system function as described below. If
it does not work, perform troubleshooting. Refer to P.42C-66.
⦆
Operate the transmitter to check that the doors and liftgate can
be locked and unlocked.
⦆
Operate the transmitter to check that the answerback function
works in response to door and liftgate locking/unlocking.
NOTE:
The hazard and horn answerback setting can be
changed using the customization function. Confirm which
setting is activated before performing these checks.
Refer to P.42C-91.
INSPECTION OF KEYLESS ENTRY TIMER LOCK
FUNCTION
M14209200051USA0000010000
Attempt to unlock the doors and the liftgate by using the
transmitter. If the doors and the liftgate are not locked within 30
seconds, carry out diagnosis. Note that the doors and the liftgate
will not be locked if the ignition key is inserted within the 30-
second period, one of the doors or the liftgate is opened. Refer
to P.42C-66.
NOTE:
The operation time of the keyless entry timer lock
function can be set using the customization function.
Confirm the operation time before performing the diagnosis.
Refer to P.42C-91.
CONFIGURATION FUNCTION
M14209200052USA0000010000
Using M.U.T.-III, the following functions can be
customized. The programmed information is held
even when the battery is disconnected.
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting
contents
(scan tool MB991958
display)
Adjusting contents
Hazard answer
back
Adjustment of the
number of keyless
hazard warning light
answer
back
flashes
Lock:1, Unlock:2
LOCK: Flashes once, UNLOCK: Flashes
twice (default)
Lock:1, Unlock:0
LOCK: Flashes once, UNLOCK: No flash
Lock:0, Unlock:2
LOCK: No flash, UNLOCK: Flash twice
Lock:2, Unlock:1
LOCK: Flash twice, UNLOCK: Flash once
Lock:2, Unlock:0
LOCK: Flash twice, UNLOCK: No flash
Lock:0, Unlock:1
LOCK: No flash, UNLOCK: Flash once
Lock:0, Unlock:0
Without function
Dome
light
delay timer with
door
Adjustment
of
interior light delay
shutdown time
0sec
0 second (no delay shutdown time)
7.5sec
7.5 seconds
WIRELESS CONTROL MODULE (WCM)
42C-91
ON-VEHICLE SERVICE
Adjustment
item (scan tool
MB991958
display)
Adjustment item
Adjusting
contents
(scan tool MB991958
display)
Adjusting contents
15sec
15 seconds
30sec
30 seconds (default)
60sec
60 seconds
120sec
120 seconds
180sec
180 seconds
Door
unlock
mode
Door lock system
All doors unlock
All the doors are unlocked when the driver's
side door is unlocked.
Dr door unlock
Only the driver's side door is unlocked when
the driver's side door is unlocked. (default)
Auto
door
unlock by P
position
Auto door unlock by
P position function
Disable
Without function (default)
Always enabled
Always with function
P/W unlocked
With function (with power window
unlocked)
Duration of horn
chirp
Horn sounding time
during horn answer
back
Short
0.01 second (default)
Long
0.02 second
Horn chirp by
RKE
Horn chirp by RKE
Not sound horn
No horn answerback function
Lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed once.
W lock any time
The horn sounds when the lock button of
keyless entry transmitter is pressed twice.
(default)
Timer lock timer Timer lock period
adjustment
30sec
30 seconds (default)
60sec
60 seconds
120sec
120 seconds
180sec
180 seconds
Duration
pre-
alarm
Adjustment of pre-
alarm continue time
10 sec
10 seconds (default)
6 sec
6 seconds
Alarm
With/without theft-
alarm function
Disable
Without function
Enable
With function (default)
Panic
alarm
switch
With/without panic
alarm function
Disable
Without function
Enable
With function (default)
TIRE PRESSURE SENSOR ID REGISTRATION
M14209200068USA0000010000
When the TPMS transmitter and/or WCM are replaced, execute
"Tire Pressure Sensor ID Registration." The TPMS won't
function until the "Tire Pressure Sensor ID Registration" has
been complete.
42C-92
WIRELESS CONTROL MODULE (WCM)
ON-VEHICLE SERVICE
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
Register the tire pressure sensor IDs as described in the
procedure below.
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
1.
Connect scan tool MB991958 to the data link connector.
2.
Turn the ignition switch to the "ON" position.
3.
Select "Interactive Diagnosis" from the start-up screen.
4.
Select "System select."
5.
Select "Special Function."
6.
Select "Tire Pressure Sensor ID Registration."
7.
Select "4tires ID Reg. (Change tire PRS.)" and start the tire
pressure sensor ID registration.
Register all tire pressure sensor IDs within twenty minutes.
8.
"4 SNSR ID Registration Do you want to start? Note Finish ID
Registration within 20 minutes." is displayed. Then, press
"OK."
9.
Decrease the tire pressure to 174 kPa or less, and register the
TPMS transmitter ID code of each wheel to WCM.
NOTE:
⦆
On completion of the TPMS transmitter ID code registration,
the TPMS transmitter ID code is displayed on the M.U.T.-III
screen.
⦆
It may take approximately one minute for the ID code to be
displayed on the M.U.T.-III screen after the tire pressure is
reduced.
⦆
If the ID code is not displayed, reduce the tire pressure
another 20 kPa or more. If the ID code is not displayed yet,
rotate the tire to displace the TPMS transmitter, and reduce
the tire pressure 20 kPa or more again.
⦆
You can start out the following operations from any TPMS
transmitter. The tire pressure sensor ID registration has no
order.
10.
"4 SNSR ID Registration Completed." is displayed. Then,
select "OK."
NOTE:
The TPMS indicator illuminates for tire pressure
alarm.
11.
After tire pressure sensor ID registration, turn the ignition
switch to the "LOCK" (OFF) position.
12.
Remove scan tool MB991958.
WIRELESS CONTROL MODULE (WCM)
42C-93
ON-VEHICLE SERVICE
TIRE PRESSURE SENSOR CHECK
M14209200069USA0000010000
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
Check the condition of the tire pressure sensor as described
below.
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
1.
Connect scan tool MB991958 to the data link connector.
2.
Turn the ignition switch to the "ON" position.
3.
Select "Interactive Diagnosis" from the start-up screen.
4.
Select "System select."
5.
Select "Special Function."
6.
Select "Tire Pressure Sensor Check."
7.
"Tire Pressure Sensor Check. Do you want to start?" is
displayed. Then, select "OK."
8.
Change the pressure of tire to be checked for 20 kPa or more.
(The tire pressure can either be decreased or increased.)
9.
Check the data on the PC display.
NOTE:
⦆
It may take approximately one minute for the ID code to be
displayed on the M.U.T.-III screen after the tire pressure is
changed.
⦆
If the ID code is not displayed, change the tire pressure
another 20 kPa or more. If the ID code is not still displayed,
rotate the tire to displace the TPMS transmitter, and change
the tire pressure 20 kPa or more again.
10.
After tire pressure sensor check, turn the ignition switch to
the "LOCK" (OFF) position.
11.
Remove scan tool MB991958.
TIRE PRESSURE SENSOR ID CHECK
M14209200070USA0000010000
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A
Check the tire pressure sensor IDs, which is registered in the
TPMS receiver, as described below.
42C-94
WIRELESS CONTROL MODULE (WCM)
ON-VEHICLE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст