Mitsubishi Outlander XL. Manual — part 834
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
1.
Connect scan tool MB991958 to the data link connector.
2.
Turn the ignition switch to the "ON" position.
3.
Select "Interactive Diagnosis" from the start-up screen.
4.
Select "System select."
5.
Choose "TPMS" from the "CHASSIS" tab.
6.
Select "MITSUBISHI."
7.
Select "Special Function."
8.
Select "Tire Pressure Sensor ID Check."
9.
Check the tire pressure sensor IDs on the PC display.
10.
After tire pressure sensor ID check, turn the ignition switch
to the "LOCK" (OFF) position.
11.
Remove scan tool MB991958.
FROM SCAN TOOL MB99158 DIAGNOSIS SCREEN
You can check the tire pressure sensor ID on the diagnosis
screen as described below.
1.
Operate scan tool MB991958 as follows:
⦆
Press "Special" button on the diagnosis screen.
⦆
Select "Tire Pressure Sensor ID Check" from the "Special
Function" menu.
2.
Check the tire pressure sensor IDs on the PC display.
3.
After tire pressure sensor ID check, turn the ignition switch to
the "LOCK" (OFF) position.
4.
Remove scan tool MB991958.
WCM
REMOVAL AND INSTALLATION
M14209200054USA0000010000
⦆
To remove the driver airbag module, refer to
GROUP 52B - Service Precautions P.
52B-28and Air Bag Module(s) and Clock
Spring P.52B-329.
⦆
When WCM has been replaced, all key ID codes
should be registered, referring to the ID code
registration necessity judgment table P.42C-8.
Pre-removal operation
⦆
Lower panel and steering column cover removal (Refer to
GROUP 52A - Instrument Panel Assembly P.52A-2.)
⦆
Clock spring column switch assembly removal (Refer to
GROUP 37 - Steering Shaft P.37-23or GROUP 52B - Air Bag
Module(s) and Clock Spring P.52B-329.)
Post-installation operation
⦆
Clock spring column switch assembly installation (Refer to
GROUP 37 - Steering Shaft P.37-23or GROUP 52B - Air Bag
Module(s) and Clock Spring P.52B-329.)
⦆
Lower panel and steering column cover installation (Refer to
GROUP 52A - Instrument Panel Assembly P.52A-2.)
WIRELESS CONTROL MODULE (WCM)
42C-95
WCM
ZC600980
1
2
AA00
2.0 ± 0.5 N·m
18 ± 4 in-lb
Removal steps
1.
Key ring illumination light
Removal steps
>>A<<
2.
WCM
INSTALLATION SERVICE POINT
>>A<< WCM INSTALATION
Check that the top claw of WCM is fixed securely to the boss of
steering lock and the antenna is not floated on the key cylinder.
TRANSMITTER
DISASSEMBLY AND ASSEMBLY
M14209200056USA0000010000
Post-installation operation
⦆
Transmitter operation check
42C-96
WIRELESS CONTROL MODULE (WCM)
TRANSMITTER
ZC600220
1
2
3
4
0000
Disassembly steps
<<A>>
1.
Upper cover
2.
Transmitter assembly
<<B>>
>>A<<
3.
Battery
Disassembly steps
4.
Master key
DISASSEMBLY SERVICE POINTS
<<A>> UPPER COVER REMOVAL
To prevent damage to the transmitter, wrap a flat-tipped
screwdriver with protective tape before prying.
ZC600348
Transmitter
Flat-tipped scr
ewdriver
0000
Insert a flat-tipped screwdriver in the area shown, and remove
the upper cover by prying it with the screwdriver.
WIRELESS CONTROL MODULE (WCM)
42C-97
TRANSMITTER
<<B>> BATTERY REMOVAL
⦆
Do not allow water or dust to enter the inside of the
transmitter assembly when it is open. Also, do not touch
the precision electronic device.
⦆
To prevent damage to the transmitter assembly, wrap a
flat-tipped screwdriver with protective tape before prying.
ZC600349
Transmitter assembly
Flat-tipped scr
ewdriver
0000
Insert a flat-tipped screwdriver in the area shown, and remove
the battery by prying it with the screwdriver.
ASSEMBLY SERVICE POINT
>>A<< BATTERY INSTALLATION
Do not allow water or dust to enter the inside of the
transmitter assembly when it is open. Also, do not touch the
precision electronic device.
ZC600350
+
Master key side
Upper
cover
side
Battery
Transmitter assembly
–
0000
Install a new battery to the transmitter assembly with its (+) side
facing towards the master key side.
Battery required for replacement: Coin type battery
CR1620
42C-98
WIRELESS CONTROL MODULE (WCM)
TRANSMITTER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст