Mitsubishi Outlander XL. Manual — part 1000
STEP 3. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect scan
tool P.54Ac-58."
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if DTC is set.
Q:Is DTC 24 set?
YES:
Go to Step 4.
NO:
The procedure is complete.
STEP 4. Check raer height sensor connector D-118 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is rear height sensor connector D-118 in good condition?
YES:
Go to Step 5.
NO:
Repair the damaged parts.
STEP 5. check rear height sensor.
Check that the rear height sensor is normal (Refer to P.
54Ac-180).
Q:Do rear height sensor work normal?
YES:
Go to Step 6.
NO:
Replace the rear height sensor.
STEP 6. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
(1)
Turn the ignition switch to the "ON" position.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
Q:Is DTC 24 set?
YES:
Go to Step 7.
NO:
The procedure is complete.
LIGHTING
54Ac-73
DIAGNOSIS
STEP 7. Check headlight automatic leveling-ECU connector
C-110 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q:Is headlight automatic leveling-ECU connector C-110 in
good condition?
YES:
Go to Step 8.
NO:
Repair the damaged parts.
STEP 8. Using scan tool MB991958, Check whether the
diagnostic trouble code is reset.
(1)
Turn the ignition switch to the "ON" position.
(2)
Erase the DTC.
(3)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(4)
Check if DTC is set.
Q:Is DTC 24 set?
YES:
Replace the headlight automatic leveling ECU.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
Code No.31 Leveling unit abnormality
M15410900085USA0000010000
Before replacing the ECU, ensure that the
communication circuit is normal.
54Ac-74
LIGHTING
DIAGNOSIS
Headlight Leveling Unit Circuit
HEADLIGHT AUTOMATIC
LEVELING-ECU
HEADLIGHT
ASSEMBLY
(LH)
HEADLIGHT
ASSEMBLY
(RH)
VOLTAGE
COMPARISON
CIRCUIT
MOTOR
DRIVE
CIRCUIT
MOTOR
DRIVE
CIRCUIT
VOLTAGE
COMPARISON
CIRCUIT
CPU
CPU
ZC6008760030
Connector: C-110
ZC6008710009
Connector: A-56
A-56 (B)
LIGHTING
54Ac-75
DIAGNOSIS
ZC6008720006
Connector: A-37
A-37 (B)
TROUBLE JUDGMENT
If the headlight leveling unit signal line is short-
circuited, DTC 31 is set.
TECHNICAL DESCRIPTION (COMMENT)
The wiring harness and connector(s) between the
headlight leveling unit and the headlight automatic
leveling-ECU, headlight assembly (headlight leveling
unit), or headlight automatic leveling-ECU may have
a problem.
TROUBLESHOOTING HINTS
⦆
Malfunction of headlight assembly (headlight
leveling unit)
⦆
Malfunction of the headlight automatic leveling-
ECU
⦆
The wiring harness or connectors may have loose,
corroded, or damaged terminals, or terminals
pushed back in the connector
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicle Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check headlight leveling unit (LH) connector
A-37,headlight automatic leveling-ECU connector C-110 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is headlight leveling unit (LH) connector A-37,headlight
automatic leveling-ECU connector C-110?
YES:
Go to Step 2.
NO:
Repair the damaged parts.
STEP 2. Check the wiring harness between headlight
leveling unit (LH) connector A-37 (terminal No. 10) and
headlight automatic leveling-ECU connector C-110
(terminal No. 3)
Q:Is wiring harness between headlight leveling unit (LH)
connector A-37 (terminal No. 10) and headlight automatic
leveling-ECU connector C-110 (terminal No. 3) in good
condition?
YES:
Go to Step 3.
NO:
Repair the wiring harness.
54Ac-76
LIGHTING
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст