Mitsubishi Outlander XL. Manual — part 952
ZC601710
1
<Front>
<Rear>
12 ± 1 N·m
102 ± 13 in-lb
3
9.0 ± 1.0 N·m
80 ± 9 in-lb
Center pillar
Second seat belt
AA00
2
Side impact sensor (front) removal
steps
<<A>>
1.
Negative (-) battery cable connection
·
Center pillar trim, lower (Refer to
GROUP 52A, Interior Trim P.52A-10).
·
Seat belt with pre-tensioner (Refer
to P.52B-345.)
<<B>>
·
Side
impact
sensor
connector
connection
2.
Side impact sensor (Front)
Side
impact
sensor
(front)
installation steps
>>A<<
·
Pre-installation inspection
>>B<<
2.
Side impact sensor (Front)
·
Side
impact
sensor
connector
connection
·
Seat belt with pre-tensioner (Refer
to P.52B-345.)
·
Center pillar trim, lower (Refer to
GROUP 52A, Interior Trim P.52A-10).
1.
Negative (-) battery cable connection
Side
impact
sensor
(front)
installation steps
>>C<<
·
Post-installation inspection
Side impact sensor (Rear) removal
steps
<<A>>
1.
Negative (-) battery cable connection
·
Quarter trim, lower (Refer to GROUP
52A, Interior Trim P.52A-10.)
<<B>>
·
Side
impact
sensor
connector
connection
3.
Side impact sensor (Rear)
Side
impact
sensor
(Rear)
installation steps
>>A<<
·
Pre-installation inspection
>>B<<
3.
Side impact sensor (Rear)
·
Side
impact
sensor
connector
connection
·
Quarter trim, lower (Refer to GROUP
52A, Interior Trim P.52A-10).
1.
Negative (-) battery cable connection
>>C<<
·
Post-installation inspection
NOTE:
The illustration above shows the side
impact sensor (RH). The position of the side
impact sensor (LH) is symmetrical to this.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-339
SIDE IMPACT SENSOR
REMOVAL SERVICE POINT
<<A>> NEGATIVE (-) BATTERY CABLE DISCONNECTION
Wait at least 60 seconds after disconnecting the battery
cable before doing any further work (Refer to P.52B-28).
Battery posts, terminals and related accessories contain
lead and lead compounds. WASH HANDS AFTER
HANDLING.
ZC500608
Battery
Insulating tape
0000
Battery cable
Disconnect the negative (-) battery cable from the battery and
tape the terminal to prevent accidental connection and air bag
deployment.
<<B>> IMPACT SENSOR CONNECTOR REMOVAL
ZC601568
Side impact sensor
Outer housing of the
impact sensor connector
0000
Slide the outer housing of the impact sensor connector in the
arrow direction shown, and disconnect the connector.
NOTE:
The illustration shows the side impact sensor (rear).
As for the impact sensor (front), follow the same procedure.
INSTALLATION SERVICE POINTS
>>A<< PRE-INSTALLATION INSPECTION
Check the side impact sensor for dents, breakage and bending
and measure the resistance between the terminals, even when
installing a new side impact sensor.
>>B <<SIDE IMPACT SENSOR INSTALLATION
If the side impact sensor is not installed securely and
correctly, the side-airbag may not operate normally.
Securely connect the connector.
52B-340
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
SIDE IMPACT SENSOR
>>C<< POST-INSTALLATION INSPECTION
ZC601295
SRS Warning light
0000
1.
Reconnect the negative (-) battery cable.
2.
Turn the ignition switch to the "ON" position.
3.
Does the "SRS" warning light illuminate for approximately
seven seconds, and go out?
4.
If yes, the SRS system is functioning properly. If not, refer
to P.52B-33.
INSPECTION
M15204000047USA0000010000
If a dent, crack, deformation or rust is detected,
replace with a new sensor.
NOTE:
For checking of the side impact sensor
other than described below, refer to the section
concerning SRS diagnosis (Refer to ).
1.
Check the side impact sensor and bracket for
dents, cracks or deformation.
2.
Check the connector for damage, and terminals for
deformation.
3.
Check that there is no bending or corrosion in the
center pillar.
CURTAIN AIR BAG MODULE
REMOVAL AND INSTALLATION
M15204000135USA0000010000
⦆
Never attempt to disassemble or repair the
curtain air bag modules. If faulty, replace it.
⦆
Do not drop the curtain air bag modules or clock
spring or allow contact with water, grease or oil.
Replace it if a dent, crack, deformation or rust is
detected.
⦆
Do not expose the curtain air bag modules to
temperatures over 93°C (200°F).
⦆
Wear gloves and safety glasses when handling
air bags that have already deployed.
⦆
An undeployed curtain air bag module should
only be disposed of in accordance with the
procedures (Refer to P.52B-352).
⦆
When removing and installing the front
passenger seat, be sure to carry out accuracy
check occupant classification sensor after the
seat has been installed in the vehicle. (On-
vehicle Service P.52B-322.)
Pre-removal Operation
⦆
Turn the ignition switch to the "LOCK" (OFF) position.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-341
SIDE IMPACT SENSOR
ZC601569
2
3
1
AA00
7.0 ± 3.0 N·m
62 ± 27 in-lb
7.0 ± 3.0 N·m
62 ± 27 in-lb
Removal steps
<<A>>
1. Negative (-) battery cable connection
·
Headlining (Refer to GROUP 52A,
Headlining P.52A-15).
<<B>>
2. Curtain air bag module connector
connection
<<C>>
3. Curtain air bag module
INSTALLATION STEPS
>>A<< ·
Pre-installation inspection
INSTALLATION STEPS
>>B<< 3. Curtain air bag module
>>C<< 2. Curtain air bag module connector
connection
·
Headlining (Refer to GROUP 52A,
Headlining P.52A-15).
1. Negative (-) battery cable connection
>>D<< ·
Post-installation inspection
REMOVAL SERVICE POINTS
<<A>> NEGATIVE (-) BATTERY CABLE DISCONNECTION
ZC500608
Battery
Insulating tape
0000
Battery cable
Wait at least 60 seconds after disconnecting the battery
cable before doing any further work. (Refer to P.52B-28).
Battery posts, terminals and related accessories contain
lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (-) battery cable from the battery and
tape the terminal to prevent accidental connection and seat belt
pre-tensioner operation.
52B-342
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
CURTAIN AIR BAG MODULE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст