Mitsubishi Outlander XL. Manual — part 598
ZC6003550000
2
2
71 ± 10 N·m
52 ± 2 ft-lb
1
1
45 ± 7 N·m
33 ± 5 ft-lb
3
1
2
4
7
5
6
8
2
71 ± 10 N·m
52 ± 2 ft-lb
1
1
39 ± 6 N·m
29 ± 4 ft-lb
Shock absorber removal steps
1.
Stabilizer link connection
<<A>>
2.
Lower arm and trailing arm connection
<<A>>
3.
Shock absorber and lower arm
connection
<<B>>
4.
Shock absorber mounting nut
5.
Shock absorber assembly
Coil spring removal steps
1.
Stabilizer link connection
Coil spring removal steps
<<A>>
2.
Lower arm and trailing arm connection
<<A>>
3.
Shock absorber and lower arm
connection
6.
Coil spring
7.
Coil spring upper pad
8.
Coil spring lower pad
REMOVAL SERVICE POINT
<<A>> LOWER ARM AND TRAILING ARM/SHOCK
ABSORBER AND LOWER ARM DISCONNECTION
ZC6021160000
Mounting
bolt
Garage
jack
While jacking-up the lower arm with the garage jack, remove the
mounting bolts.
REAR SUSPENSION
34-19
SHOCK ABSORBER ASSEMBLY
<<B>> SHOCK ABSORBER MOUNTING NUT REMOVAL
ZC3060420000
Maintenance lid
Remove the maintenance lid as shown in the figure, and then
remove the shock absorber mounting nut.
INSPECTION
M13401000026USA0000010000
⦆
Check the rubber parts for cracks and wear.
⦆
Check the shock absorber for malfunctions, oil leakage, or
abnormal noise.
DISASSEMBLY AND ASSEMBLY
M13401000027USA0000010000
ZC6003560000
25 ± 5 N·m
19 ± 3 ft-lb
3
1
2
9
4
7
5
6
8
N
Disassembly steps
<<A>>
>>A<<
1.
Self-locking nut
2.
Washer
3.
Bushing B
4.
Collar
Disassembly steps
5.
Spring upper bracket
6.
Bushing A
7.
Plate
8.
Bump rubber
34-20
REAR SUSPENSION
SHOCK ABSORBER ASSEMBLY
Disassembly steps
9.
Shock absorber
DISASSEMBLY SERVICE POINT
<<A>> SELF-LOCKING NUT REMOVAL
ZC6004200000
Piston rod
Counter the piston rod of the shock absorber as shown in the
figure to remove the self-locking nut.
ASSEMBLY SERVICE POINT
>>A<< SELF-LOCKING NUT INSTALLATION
The locking nut for the piston rod inside the shock absorber
may be loose. Do not use an impact wrench to tighten the
self-locking nut.
ZC6004200000
Piston rod
Counter the piston rod of the shock absorber as shown in the
figure, and tighten the self-locking nut to the specified torque.
Tightening torque: 25 ± 5 N·m (19 ± 3 ft-lb)
REAR SUSPENSION
34-21
SHOCK ABSORBER ASSEMBLY
STABILIZER BAR
REMOVAL AND INSTALLATION
M13401000056USA0000010000
ZC6003570000
39 ± 6 N·m
29 ± 4 ft-lb
3
1
2
4
4
31 ± 4 N·m
23 ± 3 ft-lb
39 ± 6 N·m
29 ± 4 ft-lb
<4WD>
<2WD>
Removal steps
1.
Stabilizer link
>>A<<
2.
Stabilizer bracket
>>A<<
3.
Bushing
Removal steps
>>A<<
4.
Stabilizer bar
INSTALLATION SERVICE POINTS
>>A<< STABILIZER BAR/BUSHING/STABILIZER BRACKET
INSTALLATION
ZC3058410000
Outside of the vehicle
Approx.10 mm (0.39 in)
Bushing
Stabilizer bracket
Position the identification mark of the stabilizer bar at the left side
of the vehicle as shown in the figure, and tighten the stabilizer
bracket mounting nut.
34-22
REAR SUSPENSION
STABILIZER BAR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст