Mitsubishi Outlander XL. Manual — part 165
![](/vehicles/winoney/olyerd/ierigig/cheitakul.png)
ZC600312AA00
Ø2 mm or Ø3 mm
(Ø0.08 in or
Ø0.12 in)
2.
Apply a bead of the sealant to the mating surface of the engine
lower oil pan as shown.
Specified sealant: 3M™ AAD Part No.8672, 8704,
3M™ AAD Part No.8679/8678 or equivalent
NOTE:
Install the engine lower oil pan within 15 minutes
after applying sealant.
3.
Assemble the engine lower oil pan to the engine upper oil pan.
ZC600313
Bolt specifications
Thread diameter × Length mm
M6 × 10
M6 × 10
M6 × 91
M6 × 91
M6 × 10
AA00
4.
Install the bolts to the lower oil pan as shown, and tighten them
to the specified torque.
Tightening torque: 9.5 ± 2.5 N·m (84 ± 22 in-lb)
>>C<< ENGINE OIL PAN DRAIN PLUG INSTALLATION
ZC6024380000
Engine lower
oil pan side
Replace the gasket with a new gasket. Install the new gasket in
the direction shown in the illustration.
INSPECTION
M11102000026USA0000010000
⦆
Check the oil pan for cracks.
ENGINE MECHANICAL
11A-41
OIL PAN AND OIL STRAINER
![](/vehicles/winoney/olyerd/ierigig/nedzt.png)
⦆
Check the oil pan sealant-coated surface for damage and
deformation.
⦆
Check the oil strainer for cracked, clogged or damaged wire
net and pipe.
CRANKSHAFT FRONT OIL SEAL
REMOVAL AND INSTALLATION
M11102000034USA0000010000
Pre-removal and Post-installation Operation
⦆
Timing Belt Removal and Installation (Refer to P.11A-49).
ZC600468
Engine oil
3
1
2
3
N
AA00
Removal steps
>>B<<
1.
Crankshaft sprocket
2.
Key
Removal steps
>>A<<
3.
Crankshaft front oil seal
Required Special Tool:
⦆
MD998382: Crankshaft Front Oil Seal Installer
INSTALLATION SERVICE POINTS
>>A<< CRANKSHAFT FRONT OIL SEAL INSTALLATION
1.
Apply a small amount of engine oil to the oil seal lip and then
insert the o-ring.
11A-42
ENGINE MECHANICAL
CRANKSHAFT FRONT OIL SEAL
![](/vehicles/winoney/olyerd/ierigig/hale.png)
ZC6025600000
MD998382
Crankshaft
Oil seal
2.
Using special tool MD998382, tap the oil seal into the front
case.
>>B<< CRANKSHAFT SPROCKET INSTALLATION
ZC6003530001
: Clean
Crankshaft sprocket
Crankshaft
Clean the crankshaft and crankshaft sprocket, and mount them.
CRANKSHAFT REAR OIL SEAL
REMOVAL AND INSTALLATION
M11102000037USA0000010000
Pre-removal and Post-installation Operation
⦆
Transaxle Assembly Removal and Installation (Refer to GROUP 23A, Transaxle Assembly P.23A-170).
ENGINE MECHANICAL
11A-43
CRANKSHAFT REAR OIL SEAL
![](/vehicles/winoney/olyerd/ierigig/ster.png)
ZC600469
Engine oil
4
1
2
3
4
74 ± 1 N·m
54 ± 1 ft-lb
N
AA00
Removal steps
<<A>>
>>B<<
1.
Drive plate bolts
2.
Adaptor plate
3.
Drive plate
Removal steps
>>A<<
4.
Crankshaft rear oil seal
Required Special Tools:
⦆
MB992075: Handle
⦆
MB992183: Crankshaft Rear Oil Seal Installer
⦆
MD998781: Flywheel Stopper
REMOVAL SERVICE POINT
<<A>> DRIVE PLATE BOLTS REMOVAL
ZC6017630000
MD998781
Use special tool MD998781 to secure the drive plate and remove
the drive plate bolts.
11A-44
ENGINE MECHANICAL
CRANKSHAFT REAR OIL SEAL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст