Mitsubishi Outlander XL. Manual — part 841
ROOF RAIL
REMOVAL AND INSTALLATION
M15101000166USA0000010000
ZC600423
1
4
2
3
0000
A
A
B
C
C
B
D
D
E
C
E
C
A
A
1,3
4
4
1
1,3
4
3
4
2
4
Section A – A
Section B – B
Section E – E
Section D – D
Section C – C
Claw
Claw
Claw
Claw
Claw
Claw
Claw
Claw
8.5 ± 3.5 N·m
75 ± 31 in-lb
8.5 ± 3.5 N·m
75 ± 31 in-lb
8.5 ± 3.5 N·m
75 ± 31 in-lb
Removal steps
·
Roof drip molding front (Refer to P.
51A-8)
Removal steps
1.
Front roof rail cover
EXTERIOR
51A-19
ROOF RAIL
Removal steps
2.
Center roof rail cover
3.
Rear roof rail cover
Removal steps
4.
Roof rail
LIFTGATE SPOILER
REMOVAL AND INSTALLATION
M15101000199USA0000010000
ZC600427
B
A
A
B
1
3
2
2
2
3
0000
Section A – A
Section B – B
Bolt
Rear washer
nozzle
2.5 ± 0.5 N·m
23 ± 4 in-lb
4.0 ± 2.0 N·m
35 ± 18 in-lb
Removal steps
·
Liftgate upper trim (Refer to GROUP
52A, Liftgate trim P.52A-14)
·
High-mount stop light connector
connection
Removal steps
1.
Liftgate spoiler assembly
2.
Liftgate spoiler
3.
High-mount stop light assembly
51A-20
EXTERIOR
LIFTGATE SPOILER
MARK
REMOVAL AND INSTALLATION
M15101000118USA0000010000
ZC600442
1
2
3
N
0000
1.
Front three-diamond mark (Refer to P.
51A-7)
>>A<<
2.
Rear three-diamond mark
>>A<<
3.
OUTLANDER mark
INSTALLATION SERVICE POINT
>>A<< MARK APPLICATION
1.
Installation position
Attach each mark to the position shown in the illustration.
EXTERIOR
51A-21
MARK
ZC600443
A
A
0000
13 mm
(0.51 in)
13 mm (0.51 in)
2. Rear three-diamond mark
Section A – A
Center line of
vehicle
Liftgate garnish
lower end
Liftgate garnish
upper end
ZC6004440000
58.4 mm
(2.30 in)
24.4 mm
(0.96 in)
60 mm
(2.36 in)
Application tape
Tailgate panel end
3. OUTLANDER mark
2.
Installation procedure
(1)
Use 3M™ AAD Part number 8906 or equivalent to clean
the mark installation surfaces on the body.
When attaching the marks, the ambient temperature
should be 20 - 38°C (60 - 100°F) and the air should be
completely free of dust. If the ambient temperature is
lower than 20°C (60°F), the marks and the places on the
vehicle body where the marks are to be attached should
be heated to 20 - 30°C (60 - 86°F).
(2)
Peel off the protection sheet on the back of the marks to
paste it on the installation position.
51A-22
EXTERIOR
MARK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст