Mitsubishi Outlander XL. Manual — part 842
GROUP 51B
WIPER AND WASHER
CONTENTS
GENERAL INFORMATION. . .
SPECIFICATION(S). . . ...
SERVICE SPECIFICATION. . ..
LUBRICANT. . . . . ..
SPECIAL TOOL. . . . ...
DIAGNOSIS. . . . . ..
TROUBLESHOOTING STRATEGY. ...
TROUBLE SYMPTOM CHART. . .
SYMPTOM PROCEDURES. . .
GENERAL DESCRIPTION CONCERNING THE
WIPER AND WASHER. . . .
INSPECTION PROCEDURE 1: The windshield
wipers do not work at all. ...
INSPECTION PROCEDURE 2: The windshield
wipers do not work when the wiper
switch is at the "INT", "Washer" or
"Mist" position. However, the wipers
work at low speed when the switch is at
the "Lo" and "Hi" position. ..
INSPECTION PROCEDURE 3: Windshield
wipers do not stop at the specified
park position. . . . ...
INSPECTION PROCEDURE 4: Windshield
Wipers do not work normally. .
INSPECTION PROCEDURE 5: The windshield
intermittent wiper interval cannot be
adjusted by operating the windshield
intermittent wiper volume control
switch. . . . . . ..
INSPECTION PROCEDURE 6: The windshield
intermittent wiper interval is not
changed according to the vehicle speed.
. . . . . . . .
INSPECTION PROCEDURE 7: The windshield
washer does not work. . .
INSPECTION PROCEDURE 8: Rear wiper does
not work at all. . . . .
INSPECTION PROCEDURE 9: Rear wiper does
not stop at the specified park
position. . . . . .
INSPECTION PROCEDURE 10: When the
selector lever is moved to "R" position
during the rear wiper operation, the
rear wiper does not operate at the
continuous mode. . . . .
INSPECTION PROCEDURE 11: Rear washer
does not operate. . . .
ON-VEHICLE SERVICE. . .
WINDSHIELD INTERMITTENT WIPER
INSPECTION. . . . ....
OPERATION CHECK OF REVERSE GEAR-
LINKED OPERATION OF REAR WIPER
. . . . . . . ..
CONFIGURATION FUNCTION. ....
WINDSHIELD WIPER. . . ..
REMOVAL AND INSTALLATION. ..
INSPECTION. . . . ...
WINDSHIELD WASHER. . . .
51B-1
Continued on next page
REMOVAL AND INSTALLATION. ..
INSPECTION. . . . ....
REAR WIPER AND WASHER. . .
REMOVAL AND INSTALLATION. ..
INSPECTION. . . . ....
51B-2
GENERAL INFORMATION
M15102100032USA0000010000
WINDSHIELD WIPER AND WASHER: DESCRIPTION OF CONSTRUCTION AND
OPERATION
Intermittent control (Vehicle speed-dependent variable
type) Initial condition: with function
ZC6001540000
FAST
SLOW
0
100(62)
30
0
30
Variable intermittent wiper
control switch position
Intermittent
time T1
(seconds)
Intermittent
time T1
(seconds)
Change in intermittent time by variable
intermittent wiper control switch
(when vehicle is stationary)
Change in intermittent time according
to vehicle speed
When at FAST position
When at SLOW position
Vehicle speed km/h(miles)
ZC5012780000
ON
OFF
ON
OFF
Windshield
wiper auto-
stop signal
Windshield
wiper drive
signal
T1
T1
T1
1.
ETACS calculates the windshield intermittent wiper interval
T1 from the position of the windshield intermittent wiper
switch on the column switch and the vehicle speed signal
(sent from the TCM to ETACS via CAN communication).
NOTE:
Using the customization function, the vehicle
speed-dependent intermittent function can be
invalidated. (Refer to P.51B-48.)
2.
When ETACS receives the ON signal of the windshield
intermittent wiper switch, it turns the windshield wiper drive
signal ON. When the wiper reaches the stop position, the
windshield wiper auto-stop signal turns OFF, and the
windshield wiper drive signal turns OFF.
When the intermittent time T1 calculated by step 1 has
elapsed after the windshield wiper drive signal ON, the
windshield wiper drive signal turns ON again, and the above-
mentioned operation is repeated.
WIPER AND WASHER
51B-3
GENERAL INFORMATION
Mist wiper control
ZC5012790000
ON
OFF
ON
OFF
ON
OFF
ON (HIGH)
Windshield mist
wiper switch
Windshield wiper
auto-stop signal
Windshield wiper
drive signal
Windshield wiper
speed switching
relay
OFF (LOW)
When the windshield wiper mist switch on the column switch is
turned ON while the ignition switch is in ACC or ON position, the
column switch turns the windshield wiper drive signal ON. At the
same time, the wiper speed switching relay turns ON (HI). When
the windshield mist wiper switch is ON, the windshield wiper
operates at high speed.
Low speed wiper and high speed wiper control
ZC5012800000
ON
OFF
ON
OFF
ON
OFF
(HI) ON
Windshield low-speed
wiper switch
Windshield high-speed
wiper switch
Windshield wiper auto-stop
signal
ON
OFF
Windshield wiper
drive signal
Windshield wiper speed
switching relay
(LO) OFF
Low speed operations
High speed operations
When the windshield low speed wiper switch on the
column switch is turned ON while the ignition switch
is in ACC or ON position, the column switch turns the
windshield wiper drive signal ON. Also, the wiper
speed switching relay turns OFF (LO), and the
windshield wiper operates at low speed.
When the windshield high speed wiper switch is
turned ON, the windshield wiper drive signal turns ON.
Also, the wiper speed switching relay turns ON (HI),
and the windshield wiper operates at high speed.
51B-4
WIPER AND WASHER
GENERAL INFORMATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст