Mitsubishi Outlander XL. Manual — part 176
ZK6019170000
Missing
tooth
Canvas lost and
rubber exposed
7.
Abnormal wear on teeth.
Initial stage:
Canvas worn (fluffy canvas fibers, rubbery texture
gone, white discoloration, canvas texture indistinct)
Final stage:
Canvas worn, exposing rubber (tooth width reduced)
8.
Missing tooth.
AIR BLEEDING METHOD
M11103000952USA0000010000
ZK600050
A: 3 mm
(0.12 in)
B: 11.4 mm
(0.45 in)
0000
100 to 200 N
(22 to 44 lb)
Upright
stance
⦆
Always use the vertical press and put the auto-tensioner
vertically.
⦆
For breakage prevention, Do not apply the load of 5,000
N (1,124 pound) or more to the rod.
⦆
Do not press the rod beyond Dimension "A" shown in the
illustration.
1.
Set the auto tensioner as shown in the illustration.
2.
Press the rod slowly down to the lowest point "A" shown in the
illustration.
3.
Repeat the procedure 2 three times.
4.
While the rod is projected at the point "B" shown in the
illustration, push the rod with 100 - 200 N (22 - 44 pound).
Check the enough stiffness. If the stiffness is not enough,
replace the auto tensioner.
5.
Press the rod slowly down. Put the pin through the hole and
fix it.
After the air bleeding operation has been completed, do not
tilt the auto-tensioner to 60° or more from the right angle
position.
VALVE CLEARANCE ADJUSTMENT
M11103000917USA0000010000
1.
Remove the rocker cover and ignition coil.
ZK6000560000
Timing mark
Timing mark
Camshaft sprocket
Rotate the crankshaft clockwise at any time.
2.
Turn the crankshaft clockwise, and align the crankshaft
sprocket timing mark with the position shown in the illustration.
ENGINE OVERHAUL
11B-23
TIMING BELT
ZK600057
Camshaft sprocket
Timing marks
Right bank
Left bank
0000
3.
At that time, check the right and left camshaft sprocket timing
marks are in position as shown in the illustration.
ZK600671
A
A
B
B
B
B
0000
Right bank
Left bank
A
1
3
5
A
A
B
B
A
2
4
6
<Exhaust side>
<Exhaust side>
<Intake side>
4.
Measure the valve clearances marked with arrows shown in
the illustration.
A: When No.1 cylinder is on the top dead center of
compression stroke.
B: When No.4 cylinder is on the top dead center of
compression stroke.
NOTE:
The valve clearance adjustment at the exhaust side
is not necessary because the auto lash adjuster exists.
ZK602102 AA00
5.
Using a thickness gauge, adjust the clearance between the
valve stem end and the adjusting screw.
Standard value (in cold state): 0.07 - 0.13 mm (0.003 -
0.005 inch)
NOTE:
After the engine assembly is installed on the
vehicle, check the valve clearance again in the engine
warm-up state. Adjust if necessary.
6.
Hold the adjusting screw not rotating through a driver and then
tighten the rock nut.
11B-24
ENGINE OVERHAUL
TIMING BELT
ZK6000560000
Timing mark
Timing mark
Camshaft sprocket
7.
Rotate the crankshaft one time clockwise and then align the
timing mark with the timing mark on the crankshaft sprocket.
(Place No. 4 cylinder on the top dead center of compression
stroke.)
8.
Adjust the valve clearance for the rest of the valves.
9.
Install the rocker cover and ignition coil.
INTAKE MANIFOLD
REMOVAL AND INSTALLATION
M11103000261USA0000010000
ENGINE OVERHAUL
11B-25
INTAKE MANIFOLD
ZK600038
9
22 ± 1 N·m
16 ± 1 ft-lb
1
2
4
6
5
8
3
10
11
12
12
7
10 ± 2 N·m
89 ± 17 in-lb
12 ± 1 N·m
104 ± 9 in-lb
0000
18 ± 2 N·m
13 ± 1 ft-lb
Removal steps
1.
IGNITION COIL
<<A>>
>>F<<
2.
SPARK PLUGS
<<B>>
>>E<<
3.
FUEL HIGH PRESSURE TUBE
4.
FUEL RAIL AND INJECTOR
5.
INSULATOR
>>D<<
6.
INJECTOR SUPPORT
>>C<<
7.
O-RING
Removal steps
>>B<<
8.
INJECTOR
9.
O-RING
10. FUEL RAIL
11. INTAKE MANIFOLD
>>A<<
12. INTAKE MANIFOLD GASKET
Required Special Tools:
⦆
MB991398: Spark Plug Wrench
⦆
MB992106: O-ring Installer
11B-26
ENGINE OVERHAUL
INTAKE MANIFOLD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст