Mitsubishi Outlander XL. Manual — part 746

When the door lock key cylinder is replaced by the
key set (A) in the figure, register the encrypted
code of the bar code attached to the ignition key.
Refer to GROUP 42B, ID Code Registration
Criteria Table P.42B-12the vehicle with KOS, or
GROUP 42C, ID Code Registration Criteria
Table P.42C-8vehicles without KOS.

0000

(B)

Door lock key
cylinder

ZC600090

When the door lock key cylinder is replaced by the
key set (B) in the figure, do not register the
encrypted code of the bar code attached to the
ignition key. If the encrypted code is registered,
the engine cannot start.

Pre-removal operation

｠

Door trim assembly removal (Refer to GROUP 52A, Door

Trim P.52A-11).

Post-installation operation

｠

Door inside handle play check (Refer to P.42Ab-93).

｠

Door outside handle play check (Refer to P.42Ab-92).

｠

Door trim assembly installation (Refer to GROUP 52A, Door

Trim P.52A-11.)

ZC600091

1

2

5

4

3

6

7

8

9

10

11

12

13

15

16

N

14

0000

<Front door>

25 ± 4 N·m
19 ± 3 ft-lb

7.0 ± 2.0 N·m
43 ± 17 in-lb

4.0 ± 2.0 N·m
35 ± 17 in-lb

4.0 ± 2.0 N·m
35 ± 17 in-lb

4.0 ± 2.0 N·m
35 ± 17 in-lb

5.0 ± 1.0 N·m
44 ± 9 in-lb

DOOR

42Ab-103

DOOR HANDLE AND LATCH

ZC600092

1

7

0000

Door inside handle removal

>>B<<

1.

Door inside handle
Door lock key cylinder and door
outside handle removal steps

·

Rear lower sash (Refer to P.
42Ab-110.)

2.

Plug

3.

Door outside handle cover assembly
driver's seat only

4.

Door lock key cylinder driver's seat
only

5.

Door outside handle cover

6.

Door outside handle

7.

Door outside handle gasket

8.

Door outside handle base
Door handle and door latch removal
steps

·

Rear lower sash (Refer to P.
42Ab-110.)

Door handle and door latch removal
steps

9.

Screw

10. Door latch assembly
11. Inside lock cable
12. Inside handle cable
13. Outside handle rod
14. Front door outside lock rod
15. Front door panel bracket

Door check removal steps

·

Front door speaker (Refer to GROUP
54A, Speaker P.54B-170.)

>>A<<

16. Door check

42Ab-104

DOOR

DOOR HANDLE AND LATCH

ZC600093

1

4

5

6

9

10

11

12

0000

7

N

3

<Rear door>

8

2

25 ± 4 N·m
19 ± 3 ft-lb

7.0 ± 2.0 N·m
43 ± 17 in-lb

4.0 ± 2.0 N·m
35 ± 17 in-lb

4.0 ± 2.0 N·m
35 ± 17 in-lb

5.0 ± 1.0 N·m
44 ± 9 in-lb

ZC600092

1

5

0001

Door inside handle removal

>>B<<

1.

Door inside handle
Door lock key cylinder and door
outside handle removal steps

·

Rear lower sash (Refer to P.
42Ab-110.)

2.

Plug

3.

Door outside handle cover

4.

Door outside handle

5.

Door outside handle gasket

6.

Door outside handle base
Door handle and door latch removal
steps

·

Rear lower sash (Refer to P.
42Ab-110.)

Door handle and door latch removal
steps

7.

Screw

8.

Door latch assembly

9.

Inside lock cable

10. Inside handle cable
11. Outside handle rod

Door check removal steps

·

Rear door speaker (Refer to GROUP
54A , Speaker P.54B-170.)

>>A<<

12. Door check

DOOR

42Ab-105

DOOR HANDLE AND LATCH

INSTALLATION SERVICE POINTS

>>A<< DOOR CHECK INSTALLATION

ZC6000940000

Identification mark

Install the door check with the following identification marks
facing upward.

Applicable location

Identification
mark

Front door

Left door

55L

Right door 55R

Rear door

Left door

58L

Right door 58R

>>B<< DOOR INSIDE HANDLE INSTALLATION
When connecting the inside cable to the door inside handle,
ensure that the door latch and the inside handle are unlocked.

INSPECTION

M14203000047USA0000010000

FRONT DOOR LOCK ACTUATOR CHECK

4

2
5

3
6

1

4

2
5

3
6

1

ZC600095

B

A

0000

Lever

UNLOCK

<Front left side>

<Front right side>

LOCK

View A

Lever

UNLOCK

LOCK

View B

ACTUATOR OPERATION CHECK

Lever
position

Battery
connection

Lever
operation

At

the

"LOCK"
position

｠

Connect terminal
No.4

to

the

negative battery
terminal.

｠

Connect terminal
No.6

to

the

positive battery
terminal.

The lever moves
from the "LOCK"
position to the
"UNLOCK"
position.

At

the

"UNLOCK"
position

｠

Connect terminal
No.6

to

the

negative battery
terminal.

｠

Connect terminal
No.4

to

the

positive battery
terminal.

The lever moves
from

the

"UNLOCK"
position to the
"LOCK"
position.

ACTUATOR SWITCH CHECK <DRIVER'S SIDE>

Lever position Terminal

number

Normal value

LOCK

2 - 3

Continuity exists
(2 Ω or less)

42Ab-106

DOOR

DOOR HANDLE AND LATCH