Mitsubishi Outlander XL. Manual — part 745
ZC600084
2
1
3
0000
2
<Rear door>
4.0 ± 2.0 N·m
35 ± 17 in-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
Door window glass assembly
removal steps
·
Door trim assembly (Refer to GROUP
52A, Door Trim P.52A-11.)
·
Waterproof film, belt line molding, belt
line weatherstrip inner, door window
glass channel, and speaker bracket
(Refer to P.42Ab-110.)
·
Door latch assembly (Refer to P.
42Ab-102.)
Door window glass assembly
removal steps
1.
Door window glass assembly
Power window regulator removal
steps
·
Door trim assembly (Refer to GROUP
52A, Door Trim P.52A-11.)
·
Waterproof film and speaker bracket
(Refer to P.42Ab-110.)
<<A>>
2.
Power window regulator
3.
Power window motor
Required Special Tool:
⦆
MB990480: Window Glass Holder
DOOR
42Ab-99
DOOR GLASS AND REGULATOR
ZC600087
1
2
3
4
5
6
0000
<Front door>
<Rear door>
Power window switch <Front door>
removal step
>>A<<
·
Post-installation
operation
check
<Driver’s side only>
·
Door trim assembly (Refer to GROUP
52A, Door Trim P.52A-11.)
1.
Power window switch panel assembly
2.
Power window switch panel
Power window switch <Front door>
removal step
3.
Power window main switch <Driver's
side>, power window sub switch
<Front passenger's side>
Power window sub switch <Rear
door> removal step
·
Door trim assembly (Refer to GROUP
52A, Door Trim P.52A-11.)
4.
Power window switch panel assembly
5.
Power window switch panel
6.
Power window sub switch
REMOVAL SERVICE POINT
<<A>> POWER WINDOW REGULATOR REMOVAL
1.
Remove the door window glass installation bolts.
ZC6000850000
MB990480
If tinting film is adhered to the door window glass, attach
special tool MB990480 to the outside of the glass to prevent
the film from peeling off.
2.
Lift the door window glass, and attach special tool MB990480
to the glass as shown to prevent the glass from falling.
3.
Remove the power window regulator.
42Ab-100
DOOR
DOOR GLASS AND REGULATOR
INSTALLATION SERVICE POINT
>>A<< POST-INSTALLATION OPERATION CHECK
<Driver's side only>
When the following procedures are carried out, carry out the
learning procedures of the power window fully closed position
(Refer to P.42Ab-90).
⦆
Power window regulator removal or replacement
⦆
Power window switch removal or replacement
INSPECTION
M14203000913USA0000010000
POWER WINDOW SWITCH CONTINUITY CHECK
ZC600440
8
3
4 5
1
2
6 7
<Front door>
<Rear door>
0000
Sub switch
Switch
position
Tester
connection
Specified
condition
UP
4 - 5, 6 - 7
Continuity
exists (2 Ω or
less)
OFF
4 - 5, 7 - 8
Continuity
exists (2 Ω or
less)
DOWN
4 - 6, 7 - 8
Continuity
exists (2 Ω or
less)
DOOR WINDOW REGULATOR CHECK
1.
Connect a battery directly to the motor terminals and check
that the motor runs smoothly.
2.
Check that the motor runs in the opposite direction when the
battery is connected with the polarity reversed.
3.
If a defect is found, replace the window regulator as an
assembly.
DOOR
42Ab-101
DOOR GLASS AND REGULATOR
ZC6006090000
<Front door (passenger’s side)>
Battery connection
Slider position
⦆
Connect terminal No. 1
to the negative battery
terminal.
⦆
Connect terminal No. 4
to the positive battery
terminal.
UP
⦆
Connect terminal No. 4
to the negative battery
terminal.
⦆
Connect terminal No. 1
to the positive battery
terminal.
DOWN
ZC6006080000
<Rear door>
Battery connection
Slider position
⦆
Connect terminal No. 4
to the negative battery
terminal.
⦆
Connect terminal No. 1
to the positive battery
terminal.
UP
⦆
Connect terminal No. 1
to the negative battery
terminal.
⦆
Connect terminal No. 4
to the positive battery
terminal.
DOWN
DOOR HANDLE AND LATCH
REMOVAL AND INSTALLATION
M14203000046USA0000010001
ZC6000880000
(A)
<Vehicle without KOS>
(A)
0000
<Vehicle with KOS>
ZC600089
42Ab-102
DOOR
DOOR HANDLE AND LATCH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст