Mitsubishi Outlander XL. Manual — part 967
STEP 5. Check combination meter connector C-03 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is combination meter connector C-03 in good condition?
YES:
Go to Step 6.
NO:
Repair the connector, and then go to Step 7.
STEP 6. Check the wiring harness between meter
information switch connector C-02 (terminal 1) and
combination meter connector C-03 (terminal 3).
Q:Are the wiring harness between meter information switch
connector C-02 (terminal 1) and combination meter
connector C-03 (terminal 3) in good condition?
YES:
Go to Step 7.
NO:
Repair the wiring harness, and then go to Step 7.
STEP 7. Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ab-5."
(2)
Turn the ignition switch to the "ON" position.
(3)
Erase the DTC.
(4)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(5)
Check if DTC is set.
Q:Is the DTC set?
YES:
Go to Step 1.
NO:
The procedure is complete.
DTC B2465: Ignition switch signal error
M15410100048USA0000010000
TROUBLE JUDGMENT
If 5 seconds or more elapses with the ignition switch
state and the data from the CAN communication
contradicted, the combination meter stores the DTC
B2465.
TROUBLESHOOTING HINTS
⦆
The CAN bus line may be defective
⦆
The ETACS-ECU may be defective
⦆
The combination meter may be defective
COMBINATION METER
54Ab-21
DIAGNOSIS
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Using scan tool MB991958, read the ETACS-ECU
diagnostic trouble code
Check if DTC is set to the ETACS-ECU.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ab-5."
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Troubleshoot the ETACS-ECU. Refer to P.54Ab-7.
NO:
Go to Step 2.
STEP 2. Using scan tool MB991958, diagnose the CAN bus
line.
(1)
Turn the ignition switch to the "ON" position.
(2)
Diagnose the CAN bus line.
(3)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the CAN bus line found to be normal?
YES:
Go to Step 3.
NO:
Repair the CAN bus line. (Refer to GROUP 54D,
STEP 3. Combination meter operation check
Check that the combination meter works normally.
Q:Is the check result normal?
YES:
Go to Step 4.
NO:
Check the power supply circuit of combination meter.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.
54Ab-22
COMBINATION METER
DIAGNOSIS
(1)
Erase the DTC.
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace the combination meter.
NO:
The trouble can be an intermittent malfunction (Refer
to GROUP 00 - How to use Troubleshooting/inspection
Service Points - How to Cope with Intermittent
Malfunction P.00-15).
DTC B2467: Malfunction of stepper motor
M15410100049USA0000010000
TROUBLE JUDGMENT
With the ignition switch at the ON position and the
system voltage at 10-16 volts (data from ETACS-
ECU), if the combination meter detects the stepper
motor malfunction, DTC B2467 is stored.
TROUBLESHOOTING HINTS
The combination meter may be defective
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.
COMBINATION METER
54Ab-23
DIAGNOSIS
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991958.
(1)
Connect scan tool MB991958. Refer to "How to connect the
Scan Tool (M.U.T.-III) P.54Ad-5."
(2)
Turn the ignition switch from "LOCK" (OFF) position to "ON"
position.
(3)
Check if DTC is set.
(4)
Turn the ignition switch to the "LOCK" (OFF) position.
Q:Is the DTC set?
YES:
Replace the combination meter.
NO:
The procedure is complete.
DTC U0019: Bus off(CAN-B)
M15410100055USA0000010000
⦆
If DTC U0019 is set, be sure to diagnose the CAN
bus line.
⦆
When replacing the ECU, always check that the
communication circuit is normal.
DIAGNOSTIC FUNCTION
If the CAN-B circuit malfunction occurs, the
combination meter sets DTC U0019.
JUDGMENT CRITERIA
With the ignition switch at the ON position and the
system voltage at 10 - 16 volts (data from ETACS-
ECU), if the combination meter becomes unable to
transmit data normally due to the CAN-B bus circuit
malfunction, the combination meter determines that a
problem has occurred.
TROUBLESHOOTING HINTS
The CAN bus line may be defective
DIAGNOSIS
Required Special Tools:
⦆
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
⦆
MB991824: Vehicles Communication Interface (V.C.I.)
⦆
MB991827: M.U.T.-III USB Cable
⦆
MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1.Recheck for diagnostic trouble code.
Check again if the DTC is set to the combination meter.
54Ab-24
COMBINATION METER
DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст