Mitsubishi Outlander XL. Manual — part 55
ZC6037880000
OK button
K OS/IMMO/
K e yless/TPM
S
11.
Push the OK button after "ENG Key Code Reg." is displayed.
12.
Push the OK button after "Completed." is displayed.
13.
Turn off scan tool MB991958.
14.
Turn the ignition switch to the "LOCK" (OFF) position and
then disconnect scan tool MB991958.
VIN WRITING STEPS FOR WCM AND KOS-ECU
Check that diagnostic trouble code B2416 "ECU internal
error" is not set. When diagnostic trouble code B2416 "ECU
internal error" is set, the WCM and the KOS-ECU cannot
store the VIN even if the VIN is written. If this diagnostic
trouble code is set, troubleshoot the WCM or the KOS-ECU
and repair. Then write the VIN to the WCM or the KOS-ECU.
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
Connect scan tool MB991958 to the 16-pin data link connector
as follows.
NOTE:
For details on how to use scan tool MB991958, refer
to the "M.U.T.-III Owner's Manual."
1.
Ensure that the ignition switch is at the "LOCK" (OFF) position.
2.
Start up the personal computer.
3.
Connect special tool MB991827 to special tool MB991824 and
the personal computer.
4.
Connect special tool MB991910 to the special tool MB991824.
5.
Connect special tool MB991910 to the data link connector of
the vehicle.
6.
Turn the special tool MB991824 power switch to the "ON"
position.
NOTE:
When the special tool MB991824 is energized, the
special tool MB991824 indicator light will be illuminated
in a green color.
7.
Start the "M.U.T.-III system" on the personal computer and
turn the ignition switch to the "ON" position.
System Select
Select Model Year and System
System List
Model Yea r
Vehicle In fo r matio n
Loading Option Setup
OPC
With Option
Option Name
Model Name
Model Yea r
OUTLANDER
2007
Model Code
Up to 2005 MY
From to 2006 M
Y
1
2
3
4
5
6
7
8
9
10
MPI/GDI/Diesel
KOS/IMMOBI/ Keyless/TPM S
AT/CVT/A-M
T
ABS/ASC/ASTC
SAS
Multi Select 4WD
SRS Airbag
A/C
E TA C S
Meter
ZC6037850000
OK button
8.
Select "KOS/IMMO/Keyless/TPMS" button from the "System
Select" screen. Then, select the applicable option code item
and push the OK button.
9.
Select "Coding" on the next screen.
GENERAL <BODY AND CHASSIS>
00-29
PRECAUTIONS BEFORE SERVICE
System Select
Please select function.
KOS/IMMOBI/ Keyless/TPM S
Coding
VIN W ritin g
ZC6037890000
10.
Select "VIN Writing" on "Coding" screen.
Press the OK button to execute.
VIN W ritin g
VIN currently w
ritten in ECM is displ
ayed .
W rite the number displ ayed on the screen in Immobili
zer KOS/EC U.
VIN (Engine ECU)
00000000000000000
Coding
VIN W ritin g
ZC6037900000
OK button
KOS/IMMOBI/ Keyless/TPM S
11.
Push the OK button after the VIN written in the engine control
module is displayed.
12.
Push the OK button after "VIN Writing will start. Are you
sure?" is displayed.
13.
Push the OK button after "Completed." is displayed.
KOS/IMMOBI/ Keyless/TPM S
Coding
VIN W ritin g
Result of VIN W
ritin g
VIN W ritin g
00000000000000000
ZC6037940000
14.
Result of VIN writing is displayed.
15.
Resister the other ID code. (Refer to GROUP 42B,
Troubleshooting - ID Code Registration Judgment Table P.
42B-12Vehicles
with
KOS
or
GROUP
42C,
Troubleshooting - ID Code Registration Judgment Table P.
42C-8Vehicles with WCM.)
INITIALIZATION PROCEDURE FOR LEARNING
VALUE IN MFI ENGINE
M10001000117USA0000010000
When the following service is performed, initialize the learning
value.
｠
Replacing engine assembly*
｠
Replacing throttle body and at cleaning
｠
Replacing knock sensor
NOTE:
*: Initialize A/T-related learning value.
INITIALIZATION PROCEDURE
Required Special Tools:
｠
MB991958: Scan Tool (M.U.T.-III Sub Assembly)
｠
MB991824: V.C.I.
｠
MB991827: M.U.T.-III USB Cable
｠
MB991910: M.U.T.-III Main Harness A
00-30
GENERAL <BODY AND CHASSIS>
PRECAUTIONS BEFORE SERVICE
ZC501967
AC404789
ZC5019680000
MB991824
MB991827
MB991910
Data link
connector
Connect scan tool MB991958 to the 16-pin data link connector
as follows.
NOTE:
For details on how to use scan tool MB991958, refer
to the "M.U.T.-III Owner's Manual."
1.
Ensure that the ignition switch is at the "LOCK" (OFF) position.
2.
Start up the personal computer.
3.
Connect special tool MB991827 to special tool MB991824 and
the personal computer.
4.
Connect special tool MB991910 to the special tool MB991824.
5.
Connect special tool MB991910 to the data link connector of
the vehicle.
6.
Turn the special tool MB991824 power switch to the "ON"
position.
NOTE:
When the special tool MB991824 is energized, the
special tool MB991824 indicator light will be illuminated
in a green color.
7.
Turn the ignition switch to the "ON" position.
8.
Select "Special Function" form the menu screen.
9.
Select "Learned Value Reset" form the menu screen.
10.
Initialize the learning value.
11.
After initialization of the learning value, learn the idling in MFI
engine. (Refer to LEARNING PROCEDURE FOR IDLING IN
MFI ENGINE P.00-31).
ENGINE IDLING LEARNING PROCEDURE
M10001000118USA0000010000
PURPOSE
When the ECM is replaced, or when the learned value is
initialized, the idle may not be stabilized. Carry out the learning
method by following the procedures below.
LEARNING PROCEDURE
1.
Start the engine and warm to reach 80°C (176°F) or more.
NOTE:
When the engine coolant temperature is 80°C (176°
F) or more, the warm-up is not needed if the ignition
switch is in "ON" position once.
2.
Turn the ignition switch to "LOCK" (OFF) position.
3.
After 10 seconds or more, start the engine again.
4.
For 10 minutes, carry out the idling under the condition shown
below and then confirm the engine has the normal idling.
｠
Transaxle: P range
｠
Operation in ignition-related, fan and attachments: Not to be
operated
｠
Engine coolant temperature: 80°C (176°F) or more
NOTE:
If the engine stalls while idling, check for a
dirty (on the throttle valve) of the throttle body and
GENERAL <BODY AND CHASSIS>
00-31
PRECAUTIONS BEFORE SERVICE
clean if needed. Then perform the service from Procedure
1 again.
INITIALIZATION PROCEDURE FOR THROTTLE
ACTUATOR CONTROL MOTOR
When the battery cable is disconnected and reconnected,
throttle actuator control motor valve (Fully closed position) is
eliminated, so that the throttle valve opening angle control would
not be performed correctly. When the battery cable is
disconnected and reconnected, initialize the throttle actuator
control motor using the following procedure.
1.
Turn the ignition switch to the "ON" position and then, place
the ignition switch in "LOCK" (OFF) position.
2.
For 10 seconds or more, keep the ignition switch in
"LOCK" (OFF) position.
SERVICING ELECTRICAL SYSTEM
M10001000119USA0000010000
Battery posts, terminals and related accessories contain
lead and lead compounds. WASH HANDS AFTER
HANDLING.
ZC5012600000
1.
Note the following before proceeding with working on the
electrical system.
Never perform unauthorized modifications to any electrical
device or wiring. Such modifications might lead to a vehicle
malfunction, over-capacity or short-circuit that could result in
a fire in the vehicle.
｠
Before connecting or disconnecting the negative
battery cable, be sure to turn the ignition switch to the
"LOCK" (OFF) position and turn off the lights (If this is
not done, there is the possibility of semiconductor
parts being damaged).
｠
After completion of the work (and the negative battery
terminals is connected), warm up the engine and allow
it to idle for approximately 10 minutes under the
conditions described below in order to stabilize engine
control conditions, and then check to be sure that the
idle is satisfactory.
｠
Engine coolant temperature: 85 - 95°C (185 - 203°F)
｠
Lights and all accessories: OFF
｠
Transaxle: "P" position
｠
Steering wheel: straight-forward position
2.
When servicing the electrical system, disconnect the negative
cable terminal from the battery.
00-32
GENERAL <BODY AND CHASSIS>
PRECAUTIONS BEFORE SERVICE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст