Mitsubishi Outlander XL. Manual — part 1200
(2)
Turn the ignition switch to the "ON" position.
ZC6022230019
Harness side: C-306
(3)
Measure the voltage between terminal 1 and ground.
⦆
The measured value should be approximately 12 volts
(battery positive voltage).
Q:Is the measured voltage approximately 12 volts?
YES:
Go to Step 11.
NO:
Go to Step 9.
STEP 9. Check ETACS-ECU connector C-301 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q:Is ETACS-ECU connector C-301 in good condition?
YES:
Go to Step 10.
NO:
Repair or replace the connector. Refer to GROUP 00E,
Harness Connector Inspection P.00E-2. Check that the rear
window defogger system works normally.
STEP 10. Check the wiring harness between rear window
defogger relay connector C-306 (terminal 1) and ETACS-
ECU C-301 (terminal 12).
Q:Is the wiring harness between rear window defogger relay
connector C-306 (terminal 1) and ETACS-ECU C-301
(terminal 12) in good condition?
YES:
Check that the rear window defogger system works
normally.
NO:
Repair the wiring harness. Check that the rear window
defogger system works normally.
STEP 11. Check the wiring harness between rear window
defogger relay connector C-306 (terminal 2) and A/C-ECU
connector C-119 (terminal 6).
Q:Is the wiring harness between rear window defogger relay
connector C-306 (terminal 2) and A/C-ECU connector
C-119 (terminal 6) in good condition?
YES:
Go to Step 12.
NO:
Repair or replace the wiring harness. Refer to GROUP
00E, Harness Connector Inspection P.00E-2. Check that the
rear window defogger system works normally.
STEP 12. Check the wiring harness between rear window
defogger relay connector C-306 (terminal 3) and rear
window defogger connector F-20 (terminal 1).
NOTE:
Also check intermediate connector C-32 and D-12 for
loose, corroded, or damaged terminals, or terminals pushed
back in the connector. If intermediate connector C-32 and
D-12 is damaged, repair or replace the connector as
described in GROUP 00E, Harness Connector Inspection P.
00E-2.
AIR CONDITIONING
55A-91
MANUAL A/C DIAGNOSIS
Q:Is the wiring harness between rear window defogger relay
connector C-306 (terminal 3) and rear window defogger
connector F-20 (terminal 1) in good condition?
YES:
It can be assumed that this malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunctions P.00-15.
NO:
Repair or replace the wiring harness. Refer to GROUP
00E, Harness Connector Inspection P.00E-2. Check that the
rear window defogger system works normally.
STEP 13. Check rear window defogger connector F-05 for
loose, corroded or damaged terminals, or terminals pushed
back in the connector.
Q:Is rear window defogger connector F-05 in good
condition?
YES:
Go to Step 14.
NO:
Repair or replace the connector. Refer to GROUP 00E,
Harness Connector Inspection P.00E-2. Check that the rear
window defogger system works normally.
STEP 14. Measure the resistance at rear window defogger
connector F-05.
(1)
Disconnect rear window defogger connector F-05, and
measure at the wiring harness side.
AC604249 0002
Harness side: F-05
(2)
Measure the resistance between terminal 1 and ground.
⦆
The measured value should be 2 ohms or less.
Q:Does the measured resistance value correspond with this
range?
YES:
Go to Step 16.
NO:
Go to Step 15.
STEP 15. Check the wiring harness between rear window
defogger connector F-05 (terminal 1) and the ground.
Q:Is the wiring harness between rear window defogger
connector F-05 (terminal 1) and the ground in good
condition?
YES:
Check that the rear window defogger system works
normally.
NO:
Repair or replace the wiring harness. Refer to GROUP
00E, Harness Connector Inspection P.00-15. Check that the
rear window defogger system works normally.
55A-92
AIR CONDITIONING
MANUAL A/C DIAGNOSIS
STEP 16. Check the rear window defogger.
ZC3048440000
Voltage (V)
Normal characteristics of print heater
Abnormal characteristics of print heater
Voltage (V)
12
6
0
12
6
0
(+) terminal
(-) terminal
(+) terminal
(-) terminal
Length of print heater
Length of print heater
A (middle point)
Appr oximately 6 V
Disconnection
location
(1)
Let the engine run at 2,000 r/min, and check the printed
heater with the battery fully charged.
(2)
Turn on the rear window defogger switch, and use a
voltmeter to measure the voltage in each printed heater at
middle point A on the rear window glass.
⦆
The value should be approximately 6 volts.
Q:Does the rear window defogger work normally?
YES:
Replace the A/C-ECU. Check that the rear window
defogger system works normally.
NO:
Repair the rear window defogger.
AIR CONDITIONING
55A-93
MANUAL A/C DIAGNOSIS
INSPECTION PROCEDURE 10: Blower Motor power supply system.
M15502000957USA0000010000
Blower Motor Circuit
FUSIBLE
LINK
37
BLOWER
RELAY
ETACS-
ECU
A/C-ECU
BLOWER
MOTOR
POWER
TRANSISTOR
55A-94
AIR CONDITIONING
MANUAL A/C DIAGNOSIS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст