Mitsubishi Outlander XL. Manual — part 752
ZC600113
2
1
3
0000
4
4
20 ± 5 N·m
15 ± 3 ft-lb
4.0 ± 2.0 N·m
35 ± 17 in-lb
2.5 ± 0.5 N·m
23 ± 4 in-lb
9.0 ± 1.0 N·m
79 ± 9 in-lb
Striker removal steps
·
Liftgate trim (Refer to GROUP 52A,
Liftgate Trim P.52A-14.)
>>A<<
1.
Striker
Liftgate lock release handle removal
steps
·
Liftgate trim (Refer to GROUP 52A,
Liftgate Trim P.52A-14.)
·
Rear wiper motor assembly (Refer to
GROUP 51B, Rear Wiper and
Washer P.51B-57.)
Liftgate lock release handle removal
steps
2.
Liftgate lock release handle
Liftgate latch removal steps
·
Liftgate trim (Refer to GROUP 52A,
Liftgate Trim P.52A-14.)
3.
Ground bolt
4.
Liftgate latch assembly
INSTALLATION SERVICE POINT
>>A<< STRIKER INSTALLATION
ZC6001140000
+1.5 mm
(0.06 in)
-1.5 mm
(0.06 in)
Striker center
Striker
Latch center
Latch
Install the striker so that the striker center does not deviate more
than ±1.5 mm (0.06 inch) from the latch center.
LIFTGATE
42Ac-11
LIFTGATE HANDLE AND LATCH
REMOVAL AND INSTALLATION <LIFTGATE LOWER>
M14204000017USA0000010001
Post-installation operation
⦆
Liftgate alignment (Refer to P.42Ac-4).
ZC600115
1
2
4
3
4
5
0000
20 ± 5 N·m
15 ± 3 ft-lb
2.5 ± 0.5 N·m
23 ± 4 in-lb
7.0 ± 2.0 N·m
43 ± 18 in-lb
7.0 ± 2.0 N·m
43 ± 18 in-lb
2.5 ± 0.5 N·m
23 ± 4 in-lb
:Sectional view of
clip position
Liftgate lock release handle knob
removal
1.
Liftgate lock release handle knob
Striker removal steps
1.
Liftgate lock release handle knob
·
Liftgate lower trim (Refer to GROUP
52A, Liftgate Trim P.52A-14.)
>>B<<
2.
Striker
Liftgate latch removal steps
1.
Liftgate lock release handle knob
Liftgate latch removal steps
·
Liftgate lower trim (Refer to GROUP
52A, Liftgate Trim P.52A-14.)
3.
Liftgate handle controller
4.
Liftgate latch
Liftgate weatherstrip removal
>>A<<
5.
Liftgate weatherstrip
INSTALLATION SERVICE POINTS
>>A<< LIFTGATE WEATHERSTRIP INSTALLATION
ZC6001160000
1
1
2
2
Positioning mark
1.
The marking on the liftgate weatherstrip should be positioned
at the center of the liftgate lower.
2.
Install according to the order shown in the figure.
3.
Install according to the direction shown by the arrow in the
figure.
42Ac-12
LIFTGATE
LIFTGATE HANDLE AND LATCH
>>B<< STRIKER INSTALLATION
ZC6001140000
+1.5 mm
(0.06 in)
-1.5 mm
(0.06 in)
Striker center
Striker
Latch center
Latch
Install the striker so that the striker center does not deviate more
than ±1.5 mm (0.06 in) from the latch center.
INSPECTION
M14204000012USA0000010000
LIFTGATE LOCK RELEASE HANDLE CHECK
<VEHICLES WITHOUT KEYLESS OPERATION
SYSTEM (KOS)>
ZC600117
Section A – A
0000
A
A
ON
OFF
Handle
position
Terminal
number
Normal value
ON
1 - 2
Continuity
exists (2 Ω or
less)
OFF
1 - 2
Open circuit
LIFTGATE
42Ac-13
LIFTGATE HANDLE AND LATCH
LIFTGATE LOCK RELEASE HANDLE CHECK
<VEHICLES WITH KEYLESS OPERATION
SYSTEM (KOS)>
ZC6001180000
A
A
ON
OFF
Section A – A
Liftgate lock
release handle
Lock switch
Lock switch
LIFTGATE LOCK RELEASE HANDLE
Handle
position
Terminal
number
Normal value
ON
1 - 2
Continuity
exists (2 Ω or
less)
OFF
1 - 2
Open circuit
LOCK SWITCH
Switch
position
Terminal
number
Normal value
ON
1 - 2
Continuity
exists (2 Ω or
less)
OFF
1 - 2
Open circuit
CHECK THE LIFTGATE LOCK ACTUATOR.
ZC6001190000
Lock
Lever
Unlock
Lever position Battery
connecting
terminal
number
Lever
operation
Lock
⦆
Connect
terminal No. 2
and
the
negative
battery
terminal.
⦆
Connect
terminal No. 1
and
the
positive
battery
terminal.
The
lever
moves from the
"LOCK" position
to
the
"UNLOCK"
position.
42Ac-14
LIFTGATE
LIFTGATE HANDLE AND LATCH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст