Mitsubishi Montero (2004+). Manual — part 1195
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-115
STEP 4. Check the harness for short circuit to power
supply between SRS-ECU connector E-08 (terminal No.11
and 12) and clock spring connector D-206 (terminal No.3
and 4).
Q: Are harness wires between the SRS-ECU connector
E-08 (terminal No.11 and 12) and clock spring connector
D-206 (terminal No.3 and 4) in good condition?
YES : Go to Step 5.
NO : Repair the harness wires between SRS-ECU
connector E-08 and clock spring connector D-206.
Then go to Step 5.
STEP 5. Recheck for diagnostic trouble code.
Q: Is DTC 61 set?
YES : Return to Step 1.
NO : The procedure is complete. (If no malfunctions are not
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
).
ACX01478AM
CONNECTOR: E-08
E-08 (Y)
HARNESS SIDE
CONNECTOR
(REAR VIEW)
AC204226 AF
CONNECTOR: D-206
CLOCK SPRING
D-206 (Y)
HARNESS SIDE
CONNECTOR
(REAR VIEW)
1 2
4
3
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-116
DTC 62: Driver’s Air Bag Module (Squib) System Fault for Ground Circuit (Short-Circuited to ground)
.
AIR BAG MODULE
(SQUIB)
(DRIVER'S SIDE)
CLOCK
SPRING
MICROCOMPUTER
AIR BAG DRIVE CIRCUIT
SRS-ECU
CONNECTOR
LOCK SWITCH
CONNECTOR
LOCK SWITCH
CONNECTOR
LOCK SWITCH
NOTE
: CONNECTOR
COUPLED: ON
CONNECTOR
UNCOUPLED: OFF
Driver's Air Bag Module (Squib) Circuit
AC204226AD
CLOCK SPRING
D-206 (Y)
CONNECTORS: D-206, D-229
D-229
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-117
CIRCUIT OPERATION
• The SRS-ECU judges how severe a collision is
by detecting signals from the front impact sensors
and the front air bag analog G-sensor. If the
impact is over a predetermined level, the
SRS-ECU outputs an ignition signal. At this time,
if the front air bag safing G-sensor is on, the SRS
air bag will inflate.
• The ignition signal is input to the air bag module
via the clock spring to inflate the air bag.
.
DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the driver's side air
bag module (squib). However, if no DTC resets, the
SRS warning light will be switched off (DTC will be
retained).
.
TROUBLESHOOTING HINTS
• Malfunction of the clock spring
• Damaged harness wires and connectors
• Short to the ground in the driver's air bag module
(squib) harness
• Malfunction of the SRS-ECU
.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B (Vehicles without
CAN communication system)
• MB991865: Dummy resister
• MB991866: Resister harness
STEP 1. Check the driver's air bag module. (Using scan
tool MB991958, read the diagnostic trouble code).
(1) Disconnect the negative battery terminal.
(2) By sliding the A section (in the figure) of air bag module
connector D-229 in arrow direction, disconnect the
connector.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into clock spring side air bag
module connector D-229 by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and then
recheck the diagnostic trouble code.
Q: Is DTC 62 set?
YES : Go to Step 2.
NO : Replace the driver's air bag module (Refer to
AC100441AE
D-229 AIR BAG MODULE
CONNECTOR
STEERING WHEEL
A
AC303006AD
D-229 AIR BAG
MODULE
CONNECTOR
MB991865
(DUMMY RESISTOR : 3
Ω)
MB991866 (RESISTOR
HARNESS)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-118
STEP 2. Check the clock spring. (Using scan tool
MB991958, read the diagnostic trouble code).
(1) Disconnect the negative battery terminal.
(2) Disconnect the clock spring connector D-206.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into clock spring harness side
connector D-206 (terminal No.3 and 4) by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and check the
diagnostic trouble code.
Q: Is DTC 62 set?
YES : Go to Step 3.
NO : Replace the clock spring (Refer to
). Then
go to Step 5.
AC303587
D-206 CLOCK SPRING
CONNECTOR
AD
MB991865
(DUMMY RESISTOR : 3
Ω)
MB991866 (RESISTOR
HARNESS)
1 2
4
3
(REAR VIEW)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст