Mitsubishi Montero (2004+). Manual — part 676
DOOR
TSB Revision
BODY
42-35
REMOVAL SERVICE POINT
.
<<A>> POWER WINDOW SWITCH ASSEMBLY
There is a clip (driver's side) or a claw (other sides) on the front
of the power window switch assembly. Work from the front side
using special tool MB990784.
.
<<B>> DOOR INSIDE HANDLE COVER REMOVAL
1. Insert the special tool MB990784 between the inside handle
upper part and the inside handle cover, and then disengage
the upper claw of the inside handle.
2. Disengage the lower claw of the inside handle in the same
manner as for the upper claw.
3. Remove the door trim.
4. Remove the inside handle cover from the door trim.
Y0066CA
ACX00524
POWER WINDOW SWITCH
PANEL ASSEMBLY
MB990784
AC
X0899CA
ACX00525
A
A
INSIDE HANDLE
MB990784
INSIDE HANDLE COVER
SECTION A – A
CLAW
INSIDE
HANDLE
CLAW
INSIDE
HANDLE
COVER
AB
DOOR
TSB Revision
BODY
42-36
INSTALLATION SERVICE POINT
.
>>A<< WATERPROOF FILM INSTALLATION
CAUTION
Be sure to apply the sealant below the inner panel water
drain holes so as not to plug them.
1. Install the escutcheon and the clip to the regulator handle.
2. Fully close the front door glass, and install the regulator
handle so that it faces as shown in the illustration.
INSPECTION
M1421007600558
POWER WINDOW SWITCH CONTINUITY CHECK
.
POWER WINDOW MAIN SWITCH CHECK
NOTE: *:Set switch to UNLOCK position.
.
X0084CA
X0128CA
ACX00526
INNER PANEL WATER DRAIN HOLE
<FRONT DOOR>
<REAR DOOR>
WATERPROOF FILM
WATERPROOF FILM
AB
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
FRONT
(LH)
UP
5
− 7, 3 − 8
Less than 2 ohms
OFF
3
− 7, 3 − 8, 7 − 8
Less than 2 ohms
DOWN 5
− 8, 3 − 7
Less than 2 ohms
FRONT
(RH)
UP
5
− 14, 1 − 3*
Less than 2 ohms
OFF
1
− 14, 1 − 3*, 3* − 14 Less than 2 ohms
DOWN 1
− 5, 3* − 14
Less than 2 ohms
REAR
(LH)
UP
5
− 13, 3* − 6
Less than 2 ohms
OFF
6
− 13, 3* − 6, 3* − 13 Less than 2 ohms
DOWN 5
− 6, 3* − 13
Less than 2 ohms
REAR
(RH)
UP
2
− 5, 3* − 9
Less than 2 ohms
OFF
2
− 9, 2 − 3*, 3* − 9
Less than 2 ohms
DOWN 5
− 9, 2 − 3*
Less than 2 ohms
7
6
5
4
3
2
1
14
13
12
11
10
9
8
ACX02412
DOOR
TSB Revision
BODY
42-37
POWER WINDOW SUB SWITCH CHECK <FRONT>
.
POWER WINDOW SUB SWITCH CHECK <REAR>
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
UP
5
− 8, 6 − 10
Less than 2 ohms
OFF
4
− 8, 6 − 10
Less than 2 ohms
DOWN
5
− 6, 4 − 8
Less than 2 ohms
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
UP
4
− 6, 1 − 2
Less than 2 ohms
OFF
5
− 6, 1 − 2
Less than 2 ohms
DOWN
1
− 4, 5 − 6
Less than 2 ohms
5
4
3
2
1
10
9
8
7
6
ACX02413 AE
<FRONT>
ACX00538 AC
<REAR>
DOOR
TSB Revision
BODY
42-38
DOOR GLASS AND REGULATOR
REMOVAL AND INSTALLATION
M1429001300360
Pre-removal Operation
• Door Trim and Waterproof Film Removal (Refer to
Post-installation Operation
• Door Window Glass Adjustment (Refer to
• Door Trim and Waterproof Film Removal (Refer to
AC308863
1
2
3
4
6
7
AB
5
5.4 ± 1.4 N·m
48 ± 13 in-lb
<FRONT DOOR>
DOOR WINDOW GLASS REMOVAL
STEPS
1. DOOR BELT LINE MOLDING
ASSEMBLY
2. POWER WINDOW GLASS
RUNCHANNEL
3. DOOR WINDOW GLASS
4. GLASS HOLDER
FRONT WINDOW REGULATOR
ASSEMBLY REMOVAL STEPS
5. POWER WINDOW REGULATOR
AND MOTOR ASSEMBLY
6. POWER WINDOW MOTOR
ASSEMBLY
7. POWER WINDOW REGULATOR
ASSEMBLY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст