Mitsubishi Outlander GS45X. Manual — part 503
CRANKSHAFT REAR OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-49
CRANKSHAFT REAR OIL SEAL
REMOVAL AND INSTALLATION
M1112003700888
Required Special Tools:
• MB992075: Handle
• MB992183: Crankshaft Rear Oil Seal Installer
• MD998781: Flywheel Stopper
REMOVAL SERVICE POINT
.
<<A>> DRIVE PLATE BOLTS REMOVAL
Use special tool MD998781 to secure the drive plate and
remove the drive plate bolts.
Pre-removal and Post-installation Operation
• Transaxle Assembly Removal and Installation (Refer to
GROUP 23C, Transaxle Assembly
).
AC808233
1
2
3
4
AE
4
1
Engine oil
Seating surface: Engine oil
Thread: ThreeBond 1324
N
76 ± 4 N·m
56 ± 2 ft-lb
Removal steps
<<A>>
>>B<<
1.
Drive plate bolts
2.
Adaptor plate
3.
Drive plate
>>A<<
4.
Crankshaft rear oil seal
Removal steps (Continued)
AC703058
MD998781
AB
CRANKSHAFT REAR OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-50
INSTALLATION SERVICE POINTS
.
>>A<< CRANKSHAFT REAR OIL SEAL INSTAL-
LATION
Use special tool MB992075 and MB992183, press-fit a new
crankshaft rear oil seal into the oil seal case.
.
>>B<< DRIVE PLATE BOLTS INSTALLATION
1. Cleanly remove sealant, oil and dust on the drive plate bolt,
the drive plate and the threaded portions of the crankshaft.
2. Apply oil to the drive plate and the seating surface of the
drive plate bolt.
3. Apply oil to the threaded hole of the crankshaft
4. Apply sealant to the thread of the drive plate bolts.
Specified sealant: ThreeBond 1324
5. Use special tool MD998781 to secure the drive plate in the
same manner as removal.
6. Tighten the drive plate bolts to the specified torque.
Tightening torque: 76
± 4 N⋅m (56 ± 2 ft-lb)
AC703090
Edge
Oil seal
MB992183
MB992075
MB992183
Oil seal
case
AB
MB992075
AC609795AF
AC703058
MD998781
AB
CYLINDER HEAD GASKET
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-51
CYLINDER HEAD GASKET
REMOVAL AND INSTALLATION
M1112004004118
Pre-removal and Post-installation Operation
• Intake Manifold Removal and Installation (Refer to
GROUP 15, Intake Manifold
P.15-11
).
• Exhaust Manifold Removal and Installation (Refer to
GROUP 15, Exhaust Manifold
P.15-18
).
• Timing Belt Removal and Installation (Refer to
• Thermostat Housing Removal and Installation (Refer to
GROUP 14, Water Hose and Water Pipe
P.14-45
).
• Generator Removal and Installation (Refer to GROUP 16,
Charging System
− Generator Assembly
P.16-17
).
AC809146AB
1
4
5
11
12
13
14
17
19
20
22
23
24
6
7
8
15
16
21
18
9
9
10
11
N
N
N
N
N
N
(Engine oil)
(Engine oil)
2
3
N
(Engine oil)
8.3 ± 1.0 N·m
73 ± 8 in-lb
90 ± 10 N·m
66 ± 7 ft-lb
90 ± 10 N·m
66 ± 7 ft-lb
41 ± 10 N·m
30 ± 7 ft-lb
30 ± 3 N·m
22 ± 2 ft-lb
30 ± 3 N·m
22 ± 2 ft-lb
11 ± 1 N·m
97 ± 8 in-lb
9.5 ± 2.5 N·m
84 ± 22 in-lb
8.3 ± 1.0 N·m
73 ± 8 in-lb
<Cold engine>
45 ± 2 N·m
33 ± 1 ft-lb
to
+150˚ – +154˚
9.5 ± 2.5 N·m
84 ± 22 in-lb
10 ± 2 N·m
89 ± 17 in-lb
<Cold engine>
45 ± 2 N·m
33 ± 1 ft-lb
to
+150˚ – +154˚
CYLINDER HEAD GASKET
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-52
Required Special Tools:
• MB990767: Front Hub and Flange Yoke Holder
• MB991614: Angle Gauge
• MD998719: Pin
REMOVAL SERVICE POINTS
.
<<A>> CAMSHAFT SPROCKET REMOVAL
Use special tools MB990767 and MD998719 to remove the
camshaft sprocket.
.
<<B>> CYLINDER HEAD ASSEMBLY REMOVAL
Loosen the bolts in two or three steps in the order of the num-
bers shown in the illustration, and remove them.
Removal steps
1.
PCV hose connection
2.
Engine oil dipstick
3.
O-ring
4.
Ignition coil connector
5.
Ignition coil
6.
Rocker cover
7.
Rocker cover gasket
8.
Oil pipe
9.
Gasket
10. Camshaft position sensor
connector
<<
A
>> >>
B
<< 11. Camshaft sprocket
12. Idler pulley
13. Timing belt rear cover
<<
B
>> >>
A
<< 14. Left bank cylinder head assembly
>>
A
<< 15. Cylinder head gasket
16. Breather hose connection
17. Ignition coil connector
18. Ignition coil
19. Rocker cover
20. Rocker cover gasket
21. Engine oil control valve connector
22. Engine oil pressure switch
connector
<<
B
>> >>
A
<< 23. Right bank cylinder head assembly
>>
A
<< 24. Cylinder head gasket
Removal steps (Continued)
AC703052
MB990767
MD998719
AB
AC703072
Engine front
<Right
bank>
<Left
bank>
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст