Mitsubishi Outlander GS45X. Manual — part 1365
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-83
3. Move the special tool Adjustment tool, washer nozzle
(MB992326) up and down to adjust the angle of the washer
nozzle as shown in figure (B).
NOTE: If the washer nozzle cannot be moved smoothly, adjust
the angle while pressing the special tool Adjustment tool,
washer nozzle (MB992326) against the washer nozzle.
AC900638
AC
MB992326
(A)
Mist type
washer nozzle
adjusting side
Mist type
washer
nozzle
AC900642
AC
MB992326
Mist type washer nozzle
adjusting side
Mist type
washer nozzle
(B)
AC900639
AC
MB992326
Mist type
washer nozzle
adjusting side
Mist type
washer
nozzle
B
(B)
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-84
WINDSHIELD WASHER SWITCH CHECK
Check the windshield washer switch from the ETACS diagnos-
tic trouble codes for proper operation.(Refer to GROUP 54A,
ETACS
ACA01156
414(16.3)
220
(8.7)
AC
Windshield washer
nozzle
<Left>
<Right>
Unit: mm(in)
Ceramic line terminal
112
(4.4)
115
(4.5)
537
(21.1)
400(15.7)
64(2.5)
191(7.5)
414(16.3)
79
(3.1)
75(3.0)
36(1.4)
131(5.2)
Vehicle
center line
64(2.5)
36(1.4)
75(3.0)
131(5.2)
112
(4.4)
220
(8.7)
115
(4.5)
191(7.5)
537
(21.1)
400(15.7)
79
(3.1)
300(11.8)
300(11.8)
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-85
LIGHTING CONTROL SENSOR
REMOVAL AND INSTALLATION
M1511028300020
Refer to GROUP 54A
−Lighting control sensor
).
ADAPTATION
M1511028600010
CAUTION
• Before performing the adaptation, check if the lighting
control sensor (rain sensor)-related diagnostic trouble
code is set. (if set, refer to GROUP 54A, Headlight Diag-
nostic Trouble Code Chart
).
• Turn the wiper switch to the OFF position.
1. Clean the windshield in fine weather.
2. Wipe the surface of the windshield thoroughly, and check
that the surface is dry.
3. Turn the ignition switch to the ON position.
4. Turn the ignition switch to the LOCK (OFF) position.
CAUTION
Before connecting or disconnecting scan tool MB991958,
always turn the ignition switch to the LOCK (OFF) position.
5. Connect the scan tool MB991958 to the data link connector.
6. Turn the ignition switch to the ON position.
7. Wipe the windshield surface of the lighting control sensor
section thoroughly, and check that the surface is dry.
8. Select "LIN" on the "System Select" screen, and press the
"OK" button.
9. Select "Rain light sensor" on the "System Select" screen,
and press the "OK" button.
10.Select "Special Function" on the "Rain light sensor" screen.
11.Select "Rain Sensor Adaptation" on the "Special Function"
screen.
12.Press the "OK" button, and execute the "Rain Sensor
Adaptation."
13.Press the "OK" button after the execution screen is
displayed.
14.Press the "OK" button after "Completed" is displayed.
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-86
REAR WIPER AND WASHER
GENERAL INFORMATION
M1511000101584
REAR WIPER AND WASHER
.
REAR WIPER OPERATION
• If the rear wiper and washer switch is turned to
the "INT" position with the ignition switch at
"ACC" or "ON" position, the ETACS-ECU causes
the rear wiper to operate continuously 2 times,
then intermittently at 8-second intervals.
• If the selector lever (or gearshift lever) is moved
to the "R" position when the rear wiper and
washer switch is turned to the "INT" position and
the ignition switch at "ACC" or "ON" position, the
transmission range switch (or backup light
switch) "R" turns ON. 1 second later, the
ETACS-ECU causes the rear wiper to operate
continuously 2 times to ensure good rearward
visibility. The ETACS-ECU then causes the rear
wiper to operate intermittently again at 8-second
intervals.
.
REAR WASHER OPERATION
• If the rear wiper and washer switch is turned to
the ON (washer) position with the ignition switch
at "ACC" or "ON" position, the rear washer ON
signal is sent to the ETACS-ECU, causing the
rear wiper signal to turn on after 0.9 second. After
the rear washer switch signal turns off, the rear
wiper signal turns off in 3 seconds.
• If the rear wiper and washer switch is turned to
the ON (washer) position while the rear wiper is
at intermittent mode, the rear washer works for
that period when the washer switch remains on.
Then the rear wiper returns to the intermittent
mode.
DESCRIPTION OF CONSTRUCTION AND OPERATION
.
Rear wiper control [Initial condition: 8 seconds (without successive operations)]
1. When the rear wiper switch on the column switch
is turned ON while the ignition switch is in ACC or
ON position, ETACS turns the rear wiper relay
ON for 3 seconds (for approximately 2 cycles)
and operates the intermittent action in 8 seconds
interval.
When the selector lever is moved to R (reverse)
position during the rear wiper operation, the
transmission range switch R (reverse) turns ON,
and one second after that, ETACS turns the rear
wiper relay ON for 3 seconds (for approximately 2
cycles), and operates the intermittent action in 8
seconds interval again.
2. By the special operation of the rear wiper switch
on the column switch (2 consecutive operations),
the rear wiper can operate continuously regard-
less on the set intermittent time.
AC702456 AB
t
ON
OFF
ON
OFF
ON
OFF
T2
T3
T2
T3
T1
T4
T4
T1
T4
T4
T4
T3
T2
T2
T2
T2: 7.4 seconds
Rear wiper relay
Rear wiper switch
Park/Neutral position
switch "R" position
T1: 3.0 seconds
t: 1.0 second
T3: 8.0 seconds
T4: 0.6 second
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст