Mitsubishi Outlander GS45X. Manual — part 507
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-65
CAUTION
Be careful that the finger holding the special tool
MB992276 is not pinched.
2. Slightly turn the crankshaft pulley clockwise until the special
tool MB992276 is pinched and held between the oil pump
assembly pulley and the power steering oil pump drive belt
as shown.
3. If the special tool MB992276 is held, move the finger off.
CAUTION
If the power steering oil pump drive belt is detached, be
careful that the special tool MB992276 is also detached
and fallen.
4. Slowly turn the crankshaft pulley clockwise until the power
steering oil pump drive belt goes aground on the special tool
MB992276 and is detached.
5. Remove the special tool MB992276.
.
<<C>> FUEL HIGH-PRESSURE HOSE
DISCONNECTION
1. Remove the stopper of the fuel high-pressure hose.
2. Raise the retainer of the fuel high-pressure hose and pull out
the fuel high-pressure hose in the direction shown in the
figure.
NOTE: If the retainer is released, install it securely after
removing the fuel high-pressure hose.
.
<<D>> POWER STEERING OIL PUMP ASSEMBLY
REMOVAL
1. Remove the power steering oil pump from the engine with
the hose attached.
2. Place the removed power steering oil pump in a place where
it will not be a hindrance when removing and installing the
engine assembly, and secure it with a cord or wire.
.
AC800770AC
Cord
Paper clip
MB992276
AC703084
Stopper
AB
AC703085
Retainer
AB
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-66
<<E>> A/C COMPRESSOR ASSEMBLY REMOVAL
1. Remove the A/C compressor from the A/C compressor
bracket with the hose still attached.
2. Place the removed A/C compressor where it will not be a
hindrance when removing and installing the engine
assembly, and secure it with a cord or wire.
.
<<F>> ENGINE MOUNTING BRACKET REMOVAL
1. Support the engine with a garage jack.
2. Engine hanger MB991895 is used
3. Remove special tool MB991895.
4. Engine hanger MB991928 is used
Remove special tool MB991928.
5. When removing the transaxle assembly, remove the special
tool MB992208 (Right bank) that supported the engine
assembly.
6. Mount the special tool MB991454 to the engine right hanger
and special tool MB992208 (Left bank), and support the
engine assembly using the chain block or others.
7. Place a garage jack against the engine oil pan with a piece
of wood in between so that the weight of the engine is no
longer being applied to the engine mounting bracket.
8. Loosen the engine mount mounting nuts and bolt, and
remove the engine mounting bracket.
.
<<G>> ENGINE ASSEMBLY REMOVAL
After checking that all cables, hoses and wiring harness con-
nectors and so on are disconnected from the engine, lift the
chain block slowly to remove the engine assembly upward from
the engine compartment.
AC703089
MB991895
MB991454
AB
AC703088
MB991928
MB991454
AB
AC703059
MB991454
MB992208
AB
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-67
INSTALLATION SERVICE POINTS
.
>>A<< ENGINE ASSEMBLY/ENGINE MOUNTING
INSULATOR STOPPER/ENGINE MOUNTING
BRACKET INSTALLATION
1. Install the engine assembly, being careful not to pinch the
cables, hoses or wiring harness connectors.
2. Support the engine assembly with a garage jack.
3. Mount the engine mounting insulator stopper to be
positioned as shown in the figure, then mount the engine
mounting bracket.
.
>>B<< FUEL HIGH-PRESSURE HOSE
CONNECTION
CAUTION
After connecting the fuel high-pressure hose, slightly pull
it in the pull-out direction to check that it is installed firmly.
In addition, check that there is approximately 1 mm (0.04
inch) play. After the check, install the stopper securely.
.
AC703059
MB991454
MB992208
AB
AC703066AB
Engine side
Engine mounting insulator
Engine mounting
insulator stopper
Engine mounting
bracket
AC703087
Stopper
AB
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.0L ENGINE>
11C-68
>>C<< POWER STEERING OIL PUMP DRIVE
BELT INSTALLATION
CAUTION
Check that the belt is fitted in the notches of the notched
pulley and the notches of crankshaft pulley securely.
1. Install the power steering oil pump drive belt in the
crankshaft pulley.
CAUTION
• Hang the special tool MB992275 on the vehicle compo-
nents (including front side members) using a cord and
paper clip to prevent from falling.
• Be careful that the finger holding the special tool
MB992275 is not pinched.
2. Set the special tool MB992275 and power steering oil pump
drive belt in the oil pump assembly pulley and hold it by a
finger as shown.
NOTE:
.
•
Check that the top surface of power steering oil pump
drive belt goes aground on the special tool MB992275,
and the power steering oil pump drive belt is fitted in the
notched under the oil pump assembly pulley securely as
shown.
•
Slightly turn the crankshaft pulley clockwise until the spe-
cial tool MB992275 is pinched and held between the oil
pump assembly pulley and the power steering oil pump
drive belt as shown.
3. If the special tool MB992275 is held, move the finger off.
CAUTION
If the power steering oil pump drive belt is installed, be
careful that the special tool MB992275 is detached and
fallen.
4. Slowly turn the crankshaft pulley clockwise and install the
power steering oil pump drive belt.
5. Turn the crankshaft pulley until the special tool MB992275 is
detached from the oil pump assembly and fallen, and then
remove the special tool MB992275.
6. Turn the crankshaft pulley clockwise on several times and
check that the power steering oil pump drive belt is installed
in the oil pump assembly pulley and the crankshaft pulley
securely.
AC802259AC
Notched pulley
Power steering oil pump drive belt
AC800771AC
Cord
Paper clip
MB992275
AC800768AC
Power steering
oil pump drive belt
MB992275
AC800771AC
Cord
Paper clip
MB992275
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст