Mitsubishi Outlander GS45X. Manual — part 1573
![](/vehicles/winoney/pleueamivene/yomawofeerel/ghent.png)
POWER STEERING HOSES
TSB Revision
POWER STEERING
37-55
POWER STEERING HOSES
REMOVAL AND INSTALLATION
M1372005701791
Pre-removal operation
• Power Steering Fluid Draining (Refer to
).
• Engine room Under Cover Front (A,B,C), Engine room
Side Cover, Engine room Under Cover Rear Removal
(Refer to GROUP 51
− Under Cover Removal and Installa-
<3.0L>).
• Propeller Shaft Assembly Removal (Refer to GROUP 25 −
Propeller Shaft Removal and Installation
<AWD>).
• Front Exhaust Pipe Removal (Refer to GROUP 15 −
Exhaust Pipe And Main Muffler Removal and Installation
<2.4L>,
<3.0L>).
• Front Roll Stopper And Centermember Assembly Removal
(Refer to GROUP 32
− Engine Roll Stopper and Center-
member Removal and Installation
).
Post-installation operation
• Front Roll Stopper And Centermember Assembly Installa-
tion (Refer to GROUP 32
− Engine Roll Stopper and Cen-
termember Removal and Installation
).
• Front Exhaust Pipe Installation (Refer to GROUP 15 −
Exhaust Pipe And Main Muffler Removal and Installation
<2.4L>,
<3.0L>).
• Propeller Shaft Assembly Installation (Refer to GROUP 25
− Propeller Shaft Removal and Installation
<AWD>).
• Engine room Under Cover Front (A,B,C), Engine room
Side Cover, Engine room Under Cover Rear Installation
(Refer to GROUP 51
− Under Cover Removal and Installa-
tion
<3.0L>).
• Power Steering Fluid Refilling and Bleeding (Refer to
).
AC702686
N
AR
N
11
2
4
16
5
6
8
5
6
10
13
9
N
12
14
15
7
1
3
N
57 ± 7 N·m
42 ± 5 ft-lb
15 ± 3 N·m
11 ± 2 ft-lb
<2.4L Engine>
13 ± 2 N·m
115 ± 17 in-lb
57 ± 7 N·m
42 ± 5 ft-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
5.0 ± 2.0 N·m
44 ± 17 in-lb
Removal steps
1.
Cap
2.
Oil reservoir
3.
O-ring
>>
D
4.
Suction hose
5.
Eye bolt
6.
Gasket
7.
Heat protector
>>
C
<<
8.
Pressure hose assembly
9.
Pressure hose bracket
10. Return hose
11. Return tube assembly
12. Gasket
13. Return tube
>>
A
<<
14. Clip
Removal steps (Continued)
![](/vehicles/winoney/pleueamivene/yomawofeerel/jerorevendes.png)
POWER STEERING HOSES
TSB Revision
POWER STEERING
37-56
>>
A
15. Hose clamp
>>
A
16. Return hose
Removal steps (Continued)
AC702688AH
N
14
20
4
N
5
6
11
N
8
7
12
13
15
10
17
16
9
2
1
3
N
18
19
<3.0L Engine>
5.0 ± 2.0 N·m
44 ± 17 in-lb
57 ± 7 N·m
42 ± 5 ft-lb
15 ± 3 N·m
11 ± 2 ft-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
13 ± 2 N·m
115 ± 17 in-lb
57 ± 7 N·m
42 ± 5 ft-lb
Removal steps
1.
Cap
2.
Oil reservoir
3.
O-ring
>>
D
<<
4.
Suction hose
5.
Eye bolt
6.
Gasket
7.
Eye bolt
8.
Gasket
<<A>>
9.
Heat protector
10. Hose bracket
<<A>>
>>
C
<<
11. Pressure hose assembly
12. Return hose
<<A>>
13. Return tube assembly
14. Gasket
<<A>>
15. Return tube
16. Return hose
<<A>>
17. Return tube
18. Hose clamp
19. Clip
>>
A
<<
20. Return hose
Removal steps (Continued)
![](/vehicles/winoney/pleueamivene/yomawofeerel/housoinuseru.png)
POWER STEERING HOSES
TSB Revision
POWER STEERING
37-57
REMOVAL SERVICE POINT
.
<<A>> HEAT PROTECTOR/ PRESSURE HOSE
ASSEMBLY/ RETURN TUBE ASSEMBLY/ RETURN
TUBE REMOVAL
Remove the heat protector, and push the engine assembly and
transaxle assembly toward the front of the vehicle to widen the
clearance. Then, remove the pressure hose assembly and the
return tube.
NOTE:
.
•
When pushing the engine assembly and transaxle assem-
bly, check that the propeller shaft assembly, front exhaust
pipe, front roll stopper, and center member assembly are
already removed.
INSTALLATION SERVICE POINTS
.
>>A<< RETURN HOSE/ HOSE CLAMP/ CLIP
INSTALLATION
1. Align the marking as shown in the figure and connect the
return hose.
2. Align the return hose marking within the area shown in the
figure and connect the return hose.
AC709439 AB
Marking
Return hose
AC612198AF
Marking
Return hose
Oil reservoir
![](/vehicles/winoney/pleueamivene/yomawofeerel/tintoheis.png)
POWER STEERING HOSES
TSB Revision
POWER STEERING
37-58
3. Using clip and hose clamp align the return hose marking
within the area shown in the figure and connect the return
hose.
.
>>B<< RETURN HOSE INSTALLATION
1. Align the marking as shown in the figure and connect the
return hose.
.
>>C<< PRESSURE HOSE ASSEMBLY
INSTALLATION
Align the pressure hose plate as shown in the figure and con-
nect pressure hose assembly.
.
AC507743 AD
Return hose
Marking
Marking
Clip
Clamp hose
<2.4L Engine>
AC703642 AC
Return hose
Return tube
Marking
AC709439AC
Plate
Pressure hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст