Mitsubishi Outlander GS45X. Manual — part 1540
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-29
<2.4L ENGINE: 7 persons seat, 3.0L ENGINE>
REMOVAL SERVICE POINT
.
<<A>> LOWER ARM AND TRAILING ARM/SHOCK
ABSORBER AND LOWER ARM DISCONNECTION
While jacking-up the lower arm with the garage jack, remove
the mounting bolts.
.
AC608510
45 ± 7 N·m
33 ± 5 ft-lb
3
2
4
7
5
6
39 ± 6 N·m
29 ± 4 ft-lb
AD
1
8
71 ± 10 N·m
52 ± 2 ft-lb
*1
*1
71 ± 10 N·m
52 ± 2 ft-lb
*1
*1
*2
*2
*2
Shock absorber removal steps
1.
Stabilizer link connection
<<
A
>>
2.
Lower arm and trailing arm
connection
<<
A
>>
3.
Shock absorber and lower arm
connection
<<
B
>>
4.
Shock absorber mounting nut
5.
Shock absorber assembly
Coil spring removal steps
1.
Stabilizer link connection
<<
A
>>
2.
Lower arm and trailing arm
connection
<<
A
>>
3.
Shock absorber and lower arm
connection
6.
Coil spring
7.
Coil spring upper pad
8.
Coil spring lower pad
AC608511
Mounting
bolt
AD
Garage
jack
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-30
<<B>> SHOCK ABSORBER MOUNTING NUT
REMOVAL
Remove the maintenance lid as shown in the figure, and then
remove the shock absorber mounting nut.
INSTALLATION SERVICE POINT
.
>>A<< SHOCK ABSORBER ASSEMBLY INSTAL-
LATION
Install the shock absorber assembly so that the coil spring end
faces the rear of the vehicle.
INSPECTION
M1341002600246
• Check the rubber parts for cracks and wear.
• Check the shock absorber for malfunctions, oil leakage, or
abnormal noise.
AC507198
Maintenance lid
AB
AC508628AD
Spring end
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-31
DISASSEMBLY AND ASSEMBLY <2.4L ENGINE: 5 PERSONS SEAT>
M1341002700265
Required Special Tools:
• MB991793: Spring compressor
• MB991796: Attachment B
• MB991794: Upper plate
• MB991830: Fixture
AC506862AB
1
2
3
4
5
6
7
8
9
10
11
25 ± 5 N·m
19 ± 3 ft-lb
Disassembly steps
<<
A
>> >>
B
<< 1.
Self-locking nut
2.
Washer
3.
Bushing B
4.
Collar
5.
Spring upper bracket assembly
6.
Spring upper pad
7.
Bushing A
8.
Plate
9.
Bump rubber
>>
A
<< 10. Coil spring
11. Shock absorber
Disassembly steps (Continued)
SHOCK ABSORBER ASSEMBLY
TSB Revision
REAR SUSPENSION
34-32
DISASSEMBLY SERVICE POINTS
.
<<A>> SELF-LOCKING NUT REMOVAL
CAUTION
The locking nut for the piston rod inside the shock
absorber may be loose. Do not use an impact wrench to
loosen the self-locking nut.
1. Install the special tool MB991796 to the special tool
MB991793 as shown in the figure.
2. Set the strut assembly to special tools: MB991793,
MB991796, MB991794 and MB991830.
NOTE: Use the bolts and nuts removed from the vehicle to
secure the shock absorber assembly and tighten them
lightly by hand.
3. After setting the shock absorber assembly, operate the
spring compressor and compress the coil spring by
approximately 5 mm (0.20 in).
4. While holding the piston rod as shown in the figure, remove
the self-locking nut.
.
AC209277AB
MB991796
MB991793
AC403179
MB991794
AB
MB991830
MB991796
MB991793
AC102268
AC708462 AC
Piston rod
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст