Mitsubishi Outlander GS45X. Manual — part 1633
DIAGNOSIS
TSB Revision
CVT
23A-89
DTC P0882: Malfunction of power supply system (Low)
DTC P0883: Malfunction of power supply system (high)
.
AC901225
RELAY BOX
CVT
CONTROL
RELAY
POWER SOURCE
FUSIBLE
LINK
36
TRANSAXLE
CONTROL MODULE
ENGINE
COMPARTMENT
TCM POWER SUPPLY CIRCUIT
AC709650
Connector: A-18X
AB
AC703253
Connector: C-38
Brake pedal
AB
DIAGNOSIS
TSB Revision
CVT
23A-90
DIAGNOSTIC FUNCTION
TCM monitors if power supply system is normal or
not and judges the trouble.
.
JUDGMENT CRITERIA
• <P0882> : When the engine speed is 450 r/min
or more and secondary pressure is above 0.3
MPa (44 psi), the power supply voltage is 9.0
volts or less (for 5 seconds)
• <P0883>: When the engine speed is 450 r/min or
more, the secondary pressure is above 0.3 MPa
(44 psi) and the vehicle speed is 1 km/h (0.6
mph) or more, the power supply voltage is 16.0
volts or more (for 5 seconds)
.
PROBABLE CAUSES
• Damaged wiring harness and connectors
• Malfunction of TCM
DIAGNOSTIC PROCEDURE
STEP 1. Check the following connector:
• A-18X CVT control relay connector
• C-38 TCM connector
Check each terminal for imperfect contact.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the defective connector.
STEP 2. Check for short circuit in the wiring harness
between the fusible link No.36 and the TCM connector.
• Between fusible link No.36 and C-38 TCM connector (termi-
nal No.12)
• Between fusible link No.36 and C-38 TCM connector (termi-
nal No.25)
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the wiring harness.
STEP 3. Check for open circuit in the wiring harness
between the TCM connector and the ground.
• Between C-38 TCM (terminal No.13) and ground
• Between C-38 TCM (terminal No.26) and ground
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the wiring harness.
STEP 4. Retest the system.
Recheck the trouble symptom.
Q: Does the malfunction take place again?
YES : Replace TCM.
NO : Intermittent malfunction
DIAGNOSIS
TSB Revision
CVT
23A-91
DTC P1637: Malfunction of Memory Backup
.
DIAGNOSTIC FUNCTION
TCM checks the consistency between EEPROM and
the backup memory.
.
DESCRIPTIONS OF MONITOR METHODS
• When the ignition switch is turned to the "ON"
position, TCM determines that the writing to the
EEPROM area had failed last time the ignition
switch was turned to the "LOCK" (OFF) position.
.
MONITOR EXECUTION
• Continuous
.
RELAY BOX
CVT
CONTROL
RELAY
POWER SUPPLY
BATTERY
BACK-UP
FUSIBLE
LINK
36
TRANSAXLE
CONTROL MODULE
ENGINE
COMPARTMENT
Memory backup system circuit
AC709650
Connector: A-18X
AB
AC703253
Connectors: C-37, 38
C-38
C-37
Brake pedal
AD
DIAGNOSIS
TSB Revision
CVT
23A-92
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
JUDGMENT CRITERIA
• Calculated checksum is not same as memorized
checksum.
.
OBD-II DRIVE CYCLE PATTERN
Ignition switch : ON (start the engine and keep it for
10 seconds or more)
.
PROBABLE CAUSES
• Damaged wiring harness and connectors
• Malfunction of TCM (Faulty EEPROM)
DIAGNOSTIC PROCEDURE
STEP 1. Check if diagnostic trouble code P1637 is erased
by turning the ignition switch from the "LOCK" (OFF)
position to the "ON" position.
Q: Is the check result normal?
YES : This diagnostic trouble code will be set by
disconnecting the battery. If the diagnostic trouble
code is not erased by turning the ignition switch to the
"ON" position, it is judged to be normal.
NO : Go to Step 2.
AC710015
START
Yes
No
Good
Malfunction
END
Calculated checksum memorized checksum
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст